Ring piston for Scheppach CSH56 and Woodstar CSP53
Ring piston for Scheppach CSH56 and Woodstar CSP53
Ring piston for Scheppach CSH56 and Woodstar CSP53
Piston for Scheppach CSH56 and Woodstar CSP53
Carburettor reference 3910106008 for Scheppach CSH56, Woodster CSP53 and KSB56 chainsaws
Clutch for Scheppach CSH56 and Woodstar CSP53
Launcher reference 3910106020 for chainsaw Scheppach CSH56 and Woodster KSB56
Ignition coil for garden tool 4 in 1 and brush cutter Parkside PBKS53A1 and PBKS53A2
Launcher reference 3910108024 for Parkside PBKS53A1 and PBKS53A2 chainsaws
Part 5910109008 Air Filter for Scheppach CSH56, CSP5300, Woodster CSP53 and Parkside PHKS 53A1 Benchmark 61 Chainsaws
Complete handle reference 5910109025 for chainsaw Scheppach CSH56 and Woodstar CSP53 - marker 128-162
O-ring reference 5911203042 for Scheppach CSH56, CSP5300 and Woodster CSP53 chainsaws mark 176 for G-106
Chainsaw chain reference 7910100705 for Scheppach CSH4600W/5600W and Parkside PBKS53A1
Oregon 188PXBK095 18-inch Chain Guide Part 7910100706 for Scheppach, Woodster and Parkside Chainsaws
Chainsaw chain reference 7910100717 for Scheppach CSH56, Scheppach CSP5300 and Woodster CSP53
Oregon chain holder reference 7910100718 in 50 cm and 20 inches for Scheppach CSH56V, CSP5300 and Woodster CSP53 and KSB56 chainsaws
Oregon 18-inch Reference 7910100720 Chain Guide for Scheppach and Woodster Chainsaws
Oil cap diameter 30 mm part 5910109004 for Scheppach, Woodster and Parkside chainsaws
Chainsaw guide bar reference 3904801037 for Scheppach and Woodster 4 in 1 garden tools and brushcutters as well as Parkside PBK4B3 manufactured by Scheppach only (not compatible with Grizzly)
Oil tank cap for various Scheppach chainsaws
Cylinder head gasket for Parkside PBKS53A1 and PBKS53A2 chainsaw
Complete handle for chainsaw Scheppach CSH58
Adjustment spindle tension chain reference 5910109026 for Scheppach and Woodster chainsaw
18 inch chain guide for Scheppach and Parkside chainsaws
Guide 10" Scheppach PROCUT for chainsaw ref 7910100740
10-inch chainsaw chain Scheppach Procut Ref. 7910100739 for Scheppach, Parkside and Woodster chainsaws
Oil pump ref. 3910102040 for Scheppach, Woodstar and Parkside chainsaws according to the following list: COMPATIBLE MACHINES LIST
Are you looking for a spare part for your Parkside chainsaw to repair a fault, replace a worn component or extend the service life of your equipment? At Probois Machinoutils, we offer a selection of replacement parts for various Parkside petrol chainsaws, particularly the Parkside PHKS 53 A1, PBKS 53 A1 and PBKS 53 A2 models.
A petrol chainsaw is a useful tool for cutting wood, preparing firewood and carrying out certain garden maintenance tasks. Its correct operation depends on several mechanical assemblies, including the petrol engine, ignition system, fuel supply, clutch and cutting system consisting of the guide bar and saw chain.
Over time, certain components may become worn or damaged. A blocked carburettor, faulty recoil starter, damaged ignition coil or worn saw chain can prevent the chainsaw from operating correctly.
This category includes various Parkside chainsaw spare parts for repair and maintenance operations, including pistons, piston rings, carburettors, ignition coils, recoil starters, clutches, air filters, gaskets, handles, guide bars, chains, tank caps and oil pumps.
Some references are also compatible with Scheppach and Woodster chainsaws. However, it is essential to check the models listed in each individual product description before ordering.
The Parkside PHKS 53 A1, PBKS 53 A1 and PBKS 53 A2 chainsaws are among the models for which we offer various replacement components.
These machines are equipped with a petrol engine and several mechanisms responsible for starting the engine, transmitting rotational movement and driving the saw chain.
Some components used on these models may also be fitted to Scheppach or Woodster chainsaws, particularly the Scheppach CSH56, CSP5300 and Woodster CSP53.
This compatibility between certain machines makes it easier to find replacement parts, but it does not mean that all components are interchangeable.
It is particularly important to distinguish between the PHKS 53 A1, PBKS 53 A1 and PBKS 53 A2 references. Despite sometimes having similar characteristics, different versions may require specific parts.
To identify the correct component, we recommend checking the identification plate on your chainsaw and, whenever possible, consulting the exploded parts diagram corresponding to your model.
The piston for a Parkside chainsaw is an essential component of the petrol engine. It moves inside the cylinder and helps convert the energy produced by combustion into mechanical movement.
The piston rings fitted around the piston contribute to maintaining the seal between the piston and the cylinder wall.
After many hours of operation, these components may show signs of progressive wear. Insufficient lubrication, overheating or incorrect fuel mixture settings can also cause significant damage.
A damaged piston or worn piston rings may cause several symptoms:
Our catalogue includes a piston and piston ring set for certain Parkside PHKS 53 A1 chainsaws, with compatibility also indicated for the Scheppach CSH56, CSP5300 and Woodster CSP53 models.
Before replacing these components, it is essential to inspect the condition of the cylinder and identify the original cause of the failure.
Replacing a piston or piston rings requires knowledge of petrol engine mechanics. Incorrect installation may cause further damage to the engine.
The chainsaw carburettor prepares the air-fuel mixture required for the petrol engine to operate.
It plays an important role in starting, maintaining a stable engine speed and ensuring satisfactory machine performance.
A dirty, incorrectly adjusted or damaged carburettor can cause various operating problems.
Common symptoms include:
We offer the carburettor reference 3910106008 for certain Scheppach CSH56, Woodster CSP53 and KSB56 chainsaws.
This component is included in our selection of chainsaw replacement parts. However, its compatibility with a Parkside machine must be checked individually. Its presence in this category does not guarantee that it will fit every Parkside chainsaw model.
Before replacing a carburettor, it is also advisable to inspect the air filter, fuel hoses and engine fuel supply system.
The ignition coil for a Parkside chainsaw is an electrical component of the petrol engine ignition system.
It generates the high voltage required to produce a spark at the spark plug.
Without proper ignition, the air-fuel mixture cannot ignite normally inside the cylinder.
A faulty ignition coil may cause starting difficulties, intermittent engine shutdowns or a complete absence of spark.
Our catalogue includes an ignition coil for Parkside PBKS 53 A1 and PBKS 53 A2 chainsaws.
Before ordering this component, it is important to check the exact model of your chainsaw.
A missing spark may also be caused by a defective spark plug, damaged wiring or another fault within the ignition circuit.
The recoil starter for a Parkside chainsaw is the mechanism used to turn the petrol engine manually during starting.
It generally consists of a starter handle, pull cord, return spring and a mechanism that temporarily transfers movement to the engine.
Over time, the starter cord may become worn or break. The return spring may also lose its effectiveness, while other parts of the mechanism may become damaged.
A faulty recoil starter may cause several problems:
We offer the recoil starter reference 3910108024 for Parkside PBKS 53 A1 and PBKS 53 A2 chainsaws.
Our catalogue also includes the recoil starter reference 3910106020 for certain Scheppach and Woodster chainsaws.
These references must not be considered interchangeable without checking their compatibility.
Before replacing a recoil starter, we recommend making sure that the engine can rotate freely and that the blockage is not caused by an internal mechanical problem.
The clutch for a Parkside chainsaw is a mechanical component that transfers engine power to the chain drive system when engine speed increases.
On a petrol chainsaw equipped with a centrifugal clutch, the chain should normally remain stationary when the engine is running at a correctly adjusted idle speed.
With use, clutch components may become worn or damaged.
A defective clutch may cause irregular chain movement, slipping or unusual mechanical noises.
Our catalogue includes clutch components reference 3910106013 intended for certain compatible Scheppach, Woodster and Parkside chainsaws.
Before replacing a clutch component, it is important to inspect the condition of the chain drive system as well.
If the chain rotates abnormally at idle, the machine must not be used until the problem has been identified and corrected.
The air filter for a Parkside chainsaw protects the engine by limiting the entry of dust and airborne particles into the intake system.
During woodcutting operations, the chainsaw is exposed to considerable amounts of sawdust and dust, which can gradually block the filter.
A clogged air filter can restrict airflow to the engine and reduce its performance.
Depending on its condition, the filter may need to be cleaned or replaced according to the manufacturer's recommendations.
We offer the air filter reference 5910109008, compatible with certain Parkside PHKS 53 A1, Scheppach CSH56, CSP5300 and Woodster CSP53 chainsaws.
Before ordering, check your chainsaw model and the reference of the original air filter.
The guide bar for a Parkside chainsaw guides the saw chain as it travels around the cutting system.
The chainsaw chain consists of different links, including cutting teeth responsible for cutting through wood.
Both components are subjected to considerable mechanical stress during operation and require regular inspection.
A blunt or damaged chain may reduce cutting efficiency, increase the effort required and cause premature wear to other components.
A worn guide bar may show signs of a damaged groove, burrs or uneven wear along its rails.
Our catalogue includes various chains and guide bars, including:
Other 18-inch and 20-inch guide bars and chains are also available for Scheppach and Woodster chainsaws. Their compatibility with a Parkside chainsaw must be confirmed before purchase.
Choosing the correct chain does not depend solely on the guide bar length. You must also check the chain pitch, gauge and number of drive links.
Similarly, a guide bar must be suitable for the machine's mounting system and lubrication arrangement.
The oil pump for a Parkside chainsaw contributes to lubricating the guide bar and saw chain while the machine is operating.
This lubrication is essential for reducing friction and limiting overheating of the cutting components.
Insufficient oil supply can cause accelerated wear of both the chain and guide bar.
Our catalogue includes the oil pump reference 3910102040, intended for various Scheppach, Woodster and Parkside chainsaws according to the list of compatible machines.
Before replacing the oil pump, it is advisable to check the oil level, the cleanliness of the lubrication passages and the absence of blockages in the system.
A chainsaw with a defective chain lubrication system must not be used until the problem has been resolved.
In addition to engine components and cutting accessories, certain replacement parts contribute to the handling, adjustment and general operation of the chainsaw.
Handles for Parkside chainsaws allow the operator to hold and guide the machine during use. A cracked, broken or poorly secured handle can compromise control of the tool.
We offer a complete handle reference 5910109025 for certain Parkside PHKS 53 A1, Scheppach CSH56, CSP5300 and Woodster CSP53 chainsaws.
Our selection also includes oil tank caps and fuel tank caps for various compatible models.
A damaged cap may cause leaks or allow impurities to enter the tank. It should therefore be replaced when it no longer performs its function correctly.
We also offer a chain tension adjustment rod reference 5910109026, intended for certain Scheppach, Woodster and Parkside chainsaws.
This component contributes to adjusting chain tension. A damaged adjustment mechanism may prevent the chain from being tensioned correctly.
Gaskets and seals for Parkside chainsaws play an important role in maintaining the sealing of various mechanical assemblies.
Depending on their location, they help prevent fluid leaks or maintain the sealing required for correct engine operation.
A damaged gasket can cause operating problems and must be replaced with a component suitable for its intended application.
We offer the cylinder head gasket reference 3910106017, replacing the previous reference 3910108016, for Parkside PBKS 53 A1 and PBKS 53 A2 chainsaws.
Our catalogue also includes various O-rings for certain compatible Parkside, Scheppach and Woodster chainsaws.
Before replacing an engine gasket, it is important to identify the cause of the sealing problem and inspect the condition of the mating surfaces.
To order a spare part compatible with your Parkside chainsaw, it is essential to check the information displayed on the machine's identification plate.
The Parkside brand name alone is not enough to identify the correct component. Several chainsaws may look similar while using different replacement parts.
Before ordering, we recommend checking the following information:
For chains and guide bars, also check the specific characteristics of the cutting system.
A replacement part that looks similar to the original is not necessarily compatible. It is therefore preferable to rely on the information provided in the individual product descriptions.
Regular maintenance helps preserve the performance and reliability of your Parkside petrol chainsaw.
It is important to check the cleanliness of the air filter, the condition of the chain, the tension of the cutting system and the operation of the chain lubrication system.
A correctly sharpened chain that is suitable for the machine makes cutting easier and reduces unnecessary strain on the engine.
The guide bar should also be inspected to detect abnormal wear or damage to its guiding surfaces.
Before each use, check that the safety devices, particularly the chain brake, are functioning correctly and make sure the handles are securely attached.
Maintenance operations must be carried out with the engine switched off and cooled down, following the manufacturer's instructions. When working on the cutting components, it is also advisable to disconnect the spark plug cap to prevent accidental starting.
During operation, wear appropriate personal protective equipment, including a helmet with face protection when required, hearing protection, suitable gloves, chainsaw protective trousers and appropriate safety footwear.
A chainsaw with a defective chain brake, damaged handle or faulty lubrication system must not be used until it has been repaired.
At Probois Machinoutils, we offer a selection of replacement parts for numerous machines used in woodworking, garden maintenance and DIY applications.
Our catalogue includes components for Parkside, Scheppach and Woodster chainsaws, allowing users to carry out various repair and maintenance operations.
In this category dedicated to Parkside chainsaw spare parts, you can find available components for compatible models, particularly the Parkside PHKS 53 A1, PBKS 53 A1 and PBKS 53 A2.
Whether you need a piston, piston rings, carburettor, ignition coil, recoil starter, clutch, air filter, handle, gasket, oil pump, saw chain or guide bar, consult the individual product descriptions to confirm compatibility with your machine.
Replacing a worn or defective component can help extend the service life of your chainsaw and avoid purchasing new equipment when a repair is technically possible and economically worthwhile.
Discover our selection of Parkside chainsaw spare parts at Probois Machinoutils and maintain your machine with suitable replacement components to continue your woodcutting work under reliable operating conditions.