Cylinder head for Parkside compressor
Cylinder head reference 3906129001 for Parkside compressor PKO 270 A4, PKO 500 A2, PKO 24 A1
Cylinder head reference 3906129001 for Parkside compressor PKO 270 A4, PKO 500 A2, PKO 24 A1
Reference elbow 3906129026 for Scheppach, Woodstar and Parkside compressors according to list below
Piston rings for Parkside compressor (set of 3)
Pressure gauge Ø42 G 1/8" thread for Scheppach and Parkside compressors as listed in "attached documents"
Fan for compressors Scheppach HC26, HC54, Parkside PKO 270 A4, PKO500A2 and Kity PK5400 (old reference 5906103035)
Crankcase gasket for various Parkside compressors
Oil level plug for Parkside PKO500A2, PKO270A4 and PKO24A1 compressors
Quick coupling for Scheppach, Woodster and Parkside compressor corresponding to item 57 or 58 according to the exploded views
Valve for many Scheppach, Parkside and Woodster compressors (old reference 5906103043)
Cylinder seal for various Scheppach and Parkside compressors
Air filter for Parkside compressor PKO 270 A4 and PKO 500 A2
Pressure switch for Scheppach, Zipper and Parkside compressors
Head gasket for Scheppach and Parkside compressors (Exhibit 4 on the exploded view) and for Zipper ZI-COM100-2V5
Bleed screw for different Scheppach, Woodster and Parkside compressors
Oil cap for Scheppach and Parkside compressors
Oil level plug for various Scheppach and Woodster compressors
Rubber foot part number 3906129018 for Parkside compressor PKO24A1, PKO270A4, PKO24B2 and PKO500A2
Pressure regulator Scheppach ref 3906126024 or 5906101071 or 3906129016 for compressor Scheppach, Parkside, Zipper
Safety pin Ø3 x 6 mm, Ref. 5906101007, for Scheppach, Woodster and Parkside air compressors
Are you looking for a spare part for your Parkside PKO 500 A2 air compressor to restore your machine to working condition? At Probois Machinoutils, we offer a selection of replacement parts designed for the maintenance and repair of this model, also identified as PKO500A2.
The Parkside air compressor is useful for a wide range of DIY tasks, inflation, air blowing and powering compatible pneumatic tools. Over time, certain mechanical, pneumatic or electrical components may wear out, become damaged or develop faults.
Rather than replacing the entire machine, it is often possible to carry out a repair by replacing the faulty component, provided that the part has been correctly identified and the repair is technically feasible.
This category includes cylinder heads, piston rings, cylinder head gaskets, crankcase gaskets, air filters, pressure gauges, pressure switches, pressure regulators, valves, quick-release couplings, oil plugs and other repair accessories for the Parkside PKO 500 A2 compressor.
The Parkside PKO 500 A2 air compressor consists of several assemblies involved in producing, storing and distributing compressed air. Each assembly contains components that may require inspection or replacement during the machine's service life.
Our selection of spare parts covers different components:
The availability of these components makes it easier to find a suitable repair solution without unnecessarily replacing other parts that remain in good working condition.
The cylinder head for the Parkside PKO 500 A2 compressor is an important part of the compression mechanism. It is located at the upper section of the cylinder and forms part of the compression head assembly.
A damaged cylinder head can affect the sealing or operation of the compression system, particularly if it is cracked, distorted or has damaged contact surfaces.
We offer a cylinder head, reference 3906129001, listed for several Parkside compressors, including the PKO 500 A2, PKO 270 A4 and PKO 24 A1.
Before replacing this component, it is advisable to inspect the gaskets, contact surfaces and other parts of the mechanism. Reassembly must follow the manufacturer's instructions, particularly regarding positioning and tightening requirements.
Piston rings for Parkside compressors help maintain the seal between the piston and the cylinder wall. Their function is essential for efficient air compression.
Over time, piston rings may wear or become damaged. A loss of internal sealing can contribute to reduced compression performance.
A compressor that takes unusually long to build pressure or can no longer reach its normal operating pressure may have internal wear. However, these symptoms may also be caused by an air leak, a defective valve or another mechanical problem.
This category includes a set of three piston rings for Parkside compressors.
Replacing piston rings requires disassembly of the compression mechanism. Their compatibility, correct installation position and the condition of the cylinder must be checked before any work is carried out.
Gaskets for the Parkside PKO 500 A2 compressor are essential for maintaining the sealing of the mechanical assemblies for which they are designed.
A damaged, compressed or incorrectly positioned gasket may cause an air leak or, depending on its location, an oil leak. It can also reduce performance or make a repair ineffective.
Available references include:
It is important to distinguish between these gaskets because they perform different functions and are not interchangeable.
During reassembly, the contact surfaces must be clean and in good condition. Gaskets must be installed according to the manufacturer's instructions, without altering their shape or thickness.
The air filter for the Parkside PKO 500 A2 compressor protects the compression mechanism by reducing the amount of dust and airborne particles entering the intake system.
When the filter becomes heavily clogged, the incoming airflow may decrease and affect the machine's operation.
A damaged filter may also allow more impurities to enter, potentially contributing to premature wear of internal components.
Our catalogue includes an air filter for the Parkside PKO 500 A2, also listed for the PKO 270 A4 and certain Scheppach HC55 and HC60 compressors.
To ensure correct compatibility, check the part number and filter specifications before ordering.
The pressure gauge for Parkside compressors allows users to monitor the pressure in the section of the air circuit where it is installed. A faulty pressure gauge may have a stuck needle, inaccurate readings or a damaged dial.
We offer a 42 mm pressure gauge with G 1/8" threaded connection, reference 5906102003. The dial graduations may vary depending on the version supplied by the manufacturer.
The compressor pressure switch, on the other hand, performs a control function. It helps automatically start and stop the motor according to the pressure inside the air tank.
This category includes a pressure switch, reference 3906129013, also listed for certain Scheppach and Zipper compressors.
A compressor that does not start or stop normally may have a control system problem, but the pressure switch is not necessarily responsible. An electrical and pneumatic diagnosis is essential before replacing it.
The pressure regulator for Parkside compressors allows the compressed air outlet pressure to be adjusted according to the requirements of the pneumatic accessory being used.
It should not be confused with the pressure switch, which controls motor operation.
A faulty pressure regulator may cause adjustment difficulties, unstable outlet pressure or air leakage around the component.
Our catalogue includes a Scheppach pressure regulator identified by references 3906126024, 5906101071 and 3906129016, listed for various Scheppach, Parkside and Zipper compressors.
Before ordering, it is necessary to check the original references, connections and compatibility with the exact version of your machine.
The compressed air circuit of the Parkside PKO 500 A2 contains various components responsible for air circulation and pneumatic connections.
A faulty valve, damaged elbow fitting or leaking connection may cause air loss and prevent the compressor from operating correctly.
Available parts include:
It is advisable to check the threads, dimensions and technical specifications of each fitting. Two components that look similar may have differences that prevent correct installation.
The cooling fan for Parkside compressors helps circulate air to cool certain machine components during operation.
A cracked, broken or incorrectly secured fan may cause vibrations, unusual noises or reduced cooling efficiency.
We offer a cooling fan listed for the Parkside PKO 500 A2 and PKO 270 A4 compressors, as well as certain Scheppach and Kity models. It replaces the previous reference 5906103035.
Before replacing the fan, check its dimensions, mounting system and manufacturer's reference to select the correct component.
Components related to lubrication and air tank maintenance also play an important role in keeping the compressor in good condition.
This category includes oil filler plugs and oil level plugs designed for various Parkside, Scheppach and Woodster compressors.
A damaged or unsuitable plug may compromise the seal at its installation point. Before replacing it, check the thread, dimensions and exact function of the component.
The compressor drain screw, when designed for this purpose, allows accumulated condensation water to be discharged from the air tank.
We offer a drain screw, reference 5906101066 or 10003185, with a stated diameter of 16.6 mm, for various Scheppach, Woodster and Parkside compressors.
Regularly draining the air tank according to the manufacturer's instructions helps reduce moisture accumulation and the risk of internal corrosion.
Certain mounting and support components may also require replacement after extended use.
The rubber foot for Parkside compressors helps maintain machine stability and may reduce the transmission of vibrations to the floor.
Our selection includes a rubber foot, reference 3906129018, listed for the PKO 500 A2, PKO 270 A4, PKO 24 A1 and PKO 24 B2 models.
We also offer a Ø3 x 6 mm retaining pin, reference 5906101007, for certain Scheppach, Woodster and Parkside compressors.
These small components must be replaced with parts that match the dimensions and specifications required by the manufacturer.
Before ordering a spare part for the Parkside PKO 500 A2 compressor, it is essential to check the exact model designation of your machine.
The Parkside range includes several compressors with similar reference numbers, including the PKO 24 A1, PKO 270 A4, PKO 270 A5, PKO 500 A1 and PKO 500 A2.
Although certain components are shared between several models, not all parts are interchangeable.
To avoid ordering the wrong part, we recommend the following checks:
Important: Before purchasing, check the exact model reference, month and year of manufacture, and serial number of your machine. Always consult the compatible machine list on each product page.
Several symptoms may indicate that a component of your Parkside PKO500A2 compressor needs inspection:
These symptoms must be interpreted carefully because they can have several causes. A compressor that no longer builds pressure does not automatically require replacement piston rings or a new cylinder head.
An accurate diagnosis helps identify the component actually responsible and avoids unnecessarily replacing parts that are still functioning correctly.
Regular maintenance helps extend the service life of the Parkside PKO 500 A2 air compressor. It is advisable to monitor the condition of the air filter, inspect pneumatic connections and drain the air tank according to the manufacturer's recommendations.
The oil level and lubrication requirements must be checked in accordance with the machine's user manual. Only lubricants meeting the manufacturer's specifications should be used.
Before any maintenance or repair work, switch off the compressor, disconnect it from the electrical supply and ensure that the air tank and affected circuits are completely depressurised.
Never remove a fitting, valve, pressure gauge or other pneumatic component while the circuit remains pressurised.
Repairs involving electrical components, pressure switches or safety devices must be carried out by a suitably qualified person. Safety devices must never be disabled or modified.
At Probois Machinoutils, we offer a selection of spare parts for Parkside air compressors to make the repair and maintenance of many models easier.
Our catalogue brings together replacement parts for mechanical components, pneumatic systems and maintenance items for the Parkside PKO 500 A2.
Certain parts may also be compatible with Scheppach, Woodster, Kity or Zipper compressors, provided that compatibility is explicitly stated on the product page.
Our range evolves according to parts availability and repair requirements. Our aim is to help users find the components they need to extend the service life of their equipment whenever a suitable repair is possible.
Discover our selection of spare parts for the Parkside PKO 500 A2 air compressor: cylinder heads, piston rings, gaskets, air filters, pressure gauges, pressure switches, pressure regulators, valves and other repair accessories.
Before ordering, always check the manufacturer's reference numbers and compatibility information to ensure you select the correct part for your machine.