Cylinder head for Parkside compressor
Cylinder head reference 3906129001 for Parkside compressor PKO 270 A4, PKO 500 A2, PKO 24 A1
Cylinder head reference 3906129001 for Parkside compressor PKO 270 A4, PKO 500 A2, PKO 24 A1
Reference elbow 3906129026 for Scheppach, Woodstar and Parkside compressors according to list below
Piston rings for Parkside compressor (set of 3)
Pressure gauge Ø42 G 1/8" thread for Scheppach and Parkside compressors as listed in "attached documents"
Fan for compressors Scheppach HC26, HC54, Parkside PKO 270 A4, PKO500A2 and Kity PK5400 (old reference 5906103035)
Crankcase gasket for various Parkside compressors
Oil level plug for Parkside PKO500A2, PKO270A4 and PKO24A1 compressors
Quick coupling for Scheppach, Woodster and Parkside compressor corresponding to item 57 or 58 according to the exploded views
Valve for many Scheppach, Parkside and Woodster compressors (old reference 5906103043)
Cylinder seal for various Scheppach and Parkside compressors
Air filter for Parkside compressor PKO 270 A4 and PKO 500 A2
Pressure switch for Scheppach, Zipper and Parkside compressors
Head gasket for Scheppach and Parkside compressors (Exhibit 4 on the exploded view) and for Zipper ZI-COM100-2V5
Oil cap for Scheppach and Parkside compressors
Rubber foot part number 3906129018 for Parkside compressor PKO24A1, PKO270A4, PKO24B2 and PKO500A2
Wheel axle reference 3906129028 marks 47-49 and 51 for Scheppach and Parkside compressors after 2017
Wheel axle reference 5906101084 marks 47-49 and 51 for Scheppach and Parkside compressors after 2017 and before 11/2022
Are you looking for a spare part for your Parkside PKO 270 A4 air compressor to repair a fault, replace a damaged component or maintain your equipment? At Probois Machinoutils, we offer a selection of replacement parts designed to help extend the service life of your Parkside PKO270A4 compressor.
Used for inflation, blowing, vehicle maintenance and powering certain pneumatic accessories, an air compressor is a practical piece of equipment for DIY enthusiasts and workshop users.
Over time, compression cycles, vibrations and mechanical stress can cause wear to certain components. However, an air leak, reduced performance or difficulty starting does not necessarily mean that the entire machine needs to be replaced.
Once the fault has been correctly identified, replacing the affected component may restore the compressor to normal working condition.
This category includes cylinder heads for Parkside compressors, piston rings, cylinder head and crankcase gaskets, air filters, pressure switches, pressure gauges, cooling fans, pneumatic fittings and parts for mounting and moving the compressor.
Before ordering a spare part for your Parkside PKO 270 A4 compressor, it is essential to check the exact model reference of your machine.
The Parkside range includes several models with similar names, including PKO 270 A1, PKO 270 A2, PKO 270 A3, PKO 270 A4 and PKO 270 A5.
Although these compressors have similarities, they may use different components, particularly for the cylinder head, gaskets, filtration system and mechanical assemblies.
A part compatible with the PKO 270 A3 is therefore not automatically compatible with the PKO 270 A4.
To identify your equipment correctly, we recommend recording the following information:
The Parkside PKO270A4 exploded parts diagram is a valuable resource for locating components and comparing references.
Some components are also used on Scheppach, Woodster, Zipper or Kity compressors. However, their compatibility must be checked individually.
The cylinder head for Parkside PKO 270 A4 compressor is an important component of the compression system. It forms part of the upper cylinder assembly and helps accommodate the components involved in air circulation and compression.
Our catalogue includes cylinder head reference 3906129001, intended for Parkside PKO 270 A4, PKO 500 A2 and PKO 24 A1 compressors.
A cylinder head may need replacing if it develops a crack, deformation, damage to the mating surfaces or another confirmed mechanical defect.
A problem in this assembly may cause a loss of sealing and contribute to reduced compressor performance.
However, before replacing the cylinder head, it is important to inspect the gasket, contact surfaces and associated components. An air leak does not necessarily mean that the cylinder head itself is defective.
Reassembly must follow the manufacturer's instructions, particularly regarding gasket positioning and fastener tightening.
The piston rings for Parkside compressors play an essential role in the operation of the compression mechanism.
Installed on the piston, they help provide a seal between the piston and the cylinder wall during compression.
Our selection includes a set of three piston rings for Parkside compressors.
Over time, repeated friction may gradually wear the rings. This wear can reduce sealing efficiency and affect the compressor's ability to compress air effectively.
Several symptoms may indicate that their condition should be checked:
These symptoms may also be caused by valves, gaskets or other components. A proper diagnosis is therefore necessary.
Before ordering the piston ring set, check its compatibility with your PKO 270 A4 version and the dimensions of the piston concerned.
The cylinder head gasket for Parkside compressors helps provide an airtight seal between the assembled components of the compression system.
Our catalogue includes a cylinder head gasket offered for various Scheppach, Parkside and Zipper compressors, including the Zipper ZI-COM100-2V5 according to the stated compatibility information.
This component corresponds to position 4 on certain exploded parts diagrams and replaces the previous reference 5906101003.
A damaged cylinder head gasket may cause compressed air leaks, reduced performance or an unusually long tank filling time.
When working on the cylinder head, it is advisable to inspect the gasket and the mating surfaces.
A crushed, torn or damaged gasket should not be reused if it can no longer provide adequate sealing.
It is essential to select a gasket that corresponds exactly to the compressor model and configuration.
The crankcase gasket for Parkside compressors provides sealing between the relevant sections of the motor crankcase assembly.
Our selection includes crankcase gasket reference 3906129008, corresponding to position 18 on certain Parkside compressor exploded parts diagrams.
This gasket helps prevent leaks around the mechanical assembly and maintain normal operating conditions.
It may need replacing if it is torn, deformed, excessively compressed or damaged during disassembly.
Before ordering, check the exact reference as well as the shape and dimensions of the original gasket.
During reassembly, the mating surfaces must be clean and in good condition to ensure proper sealing.
The cylinder sealing gasket for air compressors contributes to sealing certain assemblies within the compression mechanism.
Our catalogue includes gasket reference 5906115010, which replaces the previous reference 5906103010.
This part is offered for various Scheppach and Parkside compressors according to model compatibility.
A damaged cylinder gasket may contribute to air leakage and reduced compression efficiency.
Before replacement, it is important to check the condition of the mating surfaces and look for any deformation or damage that could affect assembly.
Compatibility must be confirmed using the machine reference and its corresponding exploded parts diagram.
The air filter for Parkside PKO 270 A4 compressor helps protect the compression mechanism against dust and airborne particles.
Our selection includes an air filter compatible with Parkside PKO 270 A4 and PKO 500 A2 compressors.
This filter is also offered for Scheppach HC55 and HC60 compressors.
It is important to choose the correct filter for your compressor, as different PKO 270 versions do not necessarily use the same filtration system.
A clogged filter can restrict air intake and contribute to reduced compression performance.
To maintain your machine's performance, we recommend checking the filter regularly, especially when the compressor is used in dusty environments.
A damaged, deformed or excessively dirty filter that cannot be cleaned properly should be replaced according to the manufacturer's recommendations.
The compressor should not be operated without its filtration system when one is specified by the manufacturer.
The cooling fan for Parkside PKO 270 A4 compressor helps cool the motor and limit overheating during operation.
Our catalogue includes a cooling fan compatible with Parkside PKO 270 A4 and PKO 500 A2 compressors, as well as certain Scheppach HC26, HC54 and Kity PK5400 models.
This component is associated with the previous reference 5906103035.
A damaged fan may have broken blades, cracks or a deteriorated mounting system.
A ventilation fault may cause an increase in the motor's operating temperature.
It is therefore important to inspect the fan regularly and ensure that no foreign objects interfere with its rotation.
Before ordering a replacement, compare its shape, dimensions and mounting system with those of the original fan.
The pressure switch for Parkside compressors automatically controls motor operation according to the pressure inside the receiver tank.
It normally stops the motor when pressure reaches the threshold specified by the manufacturer and allows it to restart when pressure falls to the designated level.
Our catalogue includes pressure switch reference 3906129013, offered for various Scheppach, Zipper and Parkside compressors.
A faulty pressure switch may cause several problems:
However, these symptoms may have other causes, including a power supply problem, motor fault or activated thermal protection.
The pressure switch must never be modified or adjusted arbitrarily. Any work on this electrical component or the pressure control system should be carried out by a competent person.
The pressure gauge for Parkside compressors allows users to visually monitor air pressure in the part of the circuit where it is installed.
Our selection includes pressure gauge reference 5906102003, offered for various Scheppach and Parkside compressors.
Its characteristics include:
A pressure gauge may need replacing if its needle becomes stuck, readings become inconsistent or an air leak develops around the connection.
Before ordering, check the diameter, thread, connection position and measuring range of the original gauge.
Air compressor valves are used in certain pneumatic circuits and must perform their intended function according to the machine's configuration.
Our catalogue includes valve reference 5906115043, which replaces the previous reference 5906103043.
This part is offered for various Scheppach, Parkside, Zipper and Woodster compressors according to the stated compatibility information.
A damaged valve may cause an air leak or interfere with the operation of its pneumatic circuit.
Before replacing this component, it is essential to identify the exact part and verify its reference.
This valve should not be confused with a safety valve, which performs a specific protective function against overpressure.
The elbow fitting for air compressors connects certain components of the pneumatic circuit while changing the direction of airflow.
Our selection includes elbow fitting reference 3906129026, offered for various Scheppach, Woodstar and Parkside compressors according to model compatibility.
An elbow fitting may need replacing if it develops a crack, deformation, damaged thread or persistent air leak.
Before ordering, it is important to check the reference, dimensions and connection specifications.
Installation must provide suitable sealing for the operating pressure of the relevant circuit.
The quick coupling for air compressors allows certain pneumatic accessories to be connected and disconnected easily.
Our catalogue includes a quick coupling offered for various Scheppach, Woodster, Zipper and Parkside compressors.
Depending on the exploded parts diagram, this component may correspond to position 57 or 58.
A worn quick coupling may cause an air leak or develop a locking fault.
Before ordering a replacement, check the connection type, thread and dimensions of the original component.
The oil level plug for Parkside PKO 270 A4 compressor is one of the components used for checking or closing the oil level opening, depending on the design of the mechanism.
Our selection includes an oil level plug compatible with Parkside PKO 270 A4, PKO 500 A2 and PKO 24 A1 compressors.
A damaged, cracked or poorly sealing plug may need replacing.
It is important to check the reference and dimensions of the original part before ordering.
The oil level should be checked according to the manufacturer's instructions when the compressor has a lubrication system requiring this operation.
The oil plug for air compressors closes the opening for which it is designed and helps maintain normal operating conditions.
Our catalogue includes an oil plug offered for various Scheppach and Parkside compressors.
It may need replacing if it is cracked, has a damaged thread or no longer provides an adequate seal.
Before ordering, compare the shape, dimensions and mounting system with those of the original plug.
The oil plug and oil level plug may serve different purposes depending on the compressor's design. It is therefore important not to confuse them.
The rubber foot for Parkside compressors helps stabilise the machine and reduce the transmission of certain vibrations to the floor.
Our selection includes rubber foot reference 3906129018, compatible with Parkside PKO 24 A1, PKO 270 A4, PKO 24 B2 and PKO 500 A2 compressors.
A worn, torn or missing rubber foot may reduce stability and increase vibration during operation.
Replacing it helps restore the support configuration intended by the manufacturer.
Before ordering, check the reference and mounting system of your compressor.
The wheel axle for Parkside compressors is used to mount the wheels that allow the machine to be moved.
Our catalogue includes two references:
These axles are associated with positions 47, 49 and 51 on certain exploded parts diagrams.
The two references should not be considered interchangeable without verification.
To choose the correct axle, it is important to check the manufacturing date, dimensions and original wheel mounting system.
A bent or damaged axle may make the compressor difficult to move or prevent the wheel from being secured correctly.
Our catalogue also includes a 170 mm diameter transport wheel, reference 5906103050, offered for various Scheppach compressors.
A wheel may need replacing if it is cracked, broken or excessively worn.
For the Parkside PKO 270 A4, compatibility with this wheel must be checked before ordering, particularly by comparing its diameter, bore and mounting system with those of the original wheel.
The presence of a wheel in a spare parts selection does not guarantee compatibility with every compressor version.
A Parkside PKO 270 A4 compressor that no longer builds pressure may have several different faults.
Worn piston rings, a damaged cylinder head gasket, a leaking fitting or a faulty valve may contribute to reduced performance.
A heavily clogged air filter may also restrict air intake.
The most common symptoms include:
These symptoms may have several causes. It is therefore recommended to carry out a diagnosis before replacing mechanical components.
A Parkside PKO270A4 compressor that no longer starts may have an electrical, mechanical or control system problem.
The pressure switch may be involved, but a power supply fault, defective capacitor, activated thermal protection or blocked mechanism may also prevent starting.
If the motor makes an unusual noise or appears to struggle without rotating, it is important to stop further attempts to avoid worsening the fault.
Electrical work must be carried out by a qualified person.
To order a replacement part compatible with your Parkside PKO 270 A4 compressor, several checks are recommended.
A visually identical part is not necessarily interchangeable. Differences in dimensions, mounting systems or technical specifications may prevent installation.
Regular maintenance helps preserve compressor performance and reduce the risk of certain breakdowns.
It is advisable to periodically inspect the air filter, pneumatic fittings, cooling fan, mounting components and control devices.
The oil level should be checked according to the manufacturer's instructions when the model has a lubrication system requiring this inspection.
It is also important to drain condensate from the receiver tank regularly, following the operating manual.
Particular attention should be paid to unusual noises, excessive vibrations and abnormal pressure behaviour.
Before any maintenance operation, disconnect the compressor from the electrical supply, allow it to cool and ensure that the relevant circuits are completely depressurised.
The compressed air receiver tank must never be drilled, welded or repaired using improvised methods. Safety devices must never be bypassed.
Probois Machinoutils specialises in the sale of machinery, workshop equipment, accessories and spare parts for numerous brands.
We offer a developing selection of spare parts for Parkside PKO 270 A4 air compressors to help you maintain and repair your equipment.
Our catalogue includes cylinder head reference 3906129001, piston rings, cylinder head and crankcase gaskets, an air filter, a cooling fan, a pressure switch, a pressure gauge, a valve, pneumatic fittings, oil plugs and various mounting components.
Part availability may change depending on manufacturer supplies.
Before ordering, we recommend carefully reading the product descriptions and comparing the references with those of your machine.
Whether you are looking for a cylinder head for Parkside PKO 270 A4, a cylinder head gasket, an air filter, a cooling fan or compressor piston rings, our selection helps you identify the components needed to repair your equipment.
By choosing a suitable replacement part and following the manufacturer's recommendations, you can help extend the service life of your Parkside PKO 270 A4 compressor while maintaining its performance.