Safety valve for Scheppach, Woodster and Parkside compressors
Safety valve 5906101094 or 5906115059 for Scheppach, Woodster and Parkside compressors
Safety valve 5906101094 or 5906115059 for Scheppach, Woodster and Parkside compressors
Pressure gauge Ø42 G 1/8" thread for Scheppach and Parkside compressors as listed in "attached documents"
Gasket support plate for compressor Scheppach HC50 (Exhibit 48 on the exploded view) and other references and marks such as Woodster and Parkside
Pressure regulator Scheppach ref 3906126024 or 5906101071 or 3906129016 for compressor Scheppach, Parkside, Zipper
Air filter for compressor Parkside PKO 500 A1, PKO 270 A3 and PKO 270 A5, Scheppach HC24(e) et HC50(e)
Quick coupling for Scheppach, Woodster and Parkside compressor corresponding to item 57 or 58 according to the exploded views
Valve for many Scheppach, Parkside and Woodster compressors (old reference 5906103043)
Pressure switch for Scheppach, Zipper and Parkside compressors
Bleed screw for different Scheppach, Woodster and Parkside compressors
Cylinder gasket kit n° A 1-5, 1-9, 1-13, 1-25 et 1-26 for compressor Parkside PKO 270 A5 and Scheppach HC63
Piston rings reference 39061279004 compatible with the Parkside PKO270A3 air compressor. Ideal for restoring compression and performance. Essential spare part for maintenance and repair.
Air hose ref. 3906126031 for Parkside compressor according to the following list: COMPATIBLE MACHINES LIST
Are you looking for a spare part for your Parkside PKO 270 A3 air compressor to repair a fault, replace a worn component or maintain your equipment? At Probois Machinoutils, we offer a selection of replacement parts designed to help extend the service life of your Parkside PKO270A3 compressor.
The Parkside air compressor is a practical piece of equipment for DIY projects, vehicle maintenance and various workshop applications. It can be used to inflate tyres, perform blowing operations and power pneumatic accessories compatible with its technical specifications.
Over time, compression cycles, vibrations, temperature changes and mechanical wear can lead to reduced performance or failure of certain components.
A compressor that no longer builds pressure correctly, develops an air leak or has a motor that will not start does not necessarily need to be replaced entirely. Once the cause has been correctly diagnosed, replacing the faulty part may restore normal operation.
This category includes piston rings for Parkside PKO 270 A3, pressure regulators, pressure switches, valves, air filters, pressure gauges, safety valves, pneumatic fittings and maintenance accessories.
Before ordering a spare part for your Parkside PKO 270 A3 compressor, it is essential to check the exact model reference of your machine.
The Parkside range includes several models with similar names: PKO 270 A1, PKO 270 A2, PKO 270 A3, PKO 270 A4 and PKO 270 A5.
Despite their similarities, these different versions may feature different mechanical components, filtration systems or pneumatic connections.
A part compatible with the PKO 270 A2 is therefore not automatically suitable for the PKO 270 A3.
To identify your compressor, check its identification plate and record the following information:
The Parkside PKO270A3 exploded parts diagram helps locate the various components and compare their references with the spare parts available in our catalogue.
Some components are also used on Scheppach, Woodster or Zipper compressors. However, it is essential to check the compatibility information provided on each product page.
The piston rings for Parkside PKO 270 A3 compressor are essential components of the compression system.
Installed on the piston, they help provide an airtight seal between the piston and the cylinder wall during compression.
This sealing action helps limit air losses and maintain the performance of the mechanism.
Our catalogue includes piston rings reference 39061279004, compatible with the Parkside PKO270A3 compressor.
Over time, piston rings may gradually wear due to friction and mechanical stress.
Worn or damaged piston rings may cause several symptoms:
These symptoms may also result from other components. Before replacing the piston rings, it is therefore important to inspect the cylinder, piston and associated parts.
Replacing piston rings requires mechanical disassembly and must be carried out carefully to avoid damaging the components.
The Parkside compressor pressure regulator allows the air pressure available at the machine outlet to be adjusted according to the requirements of the pneumatic accessory being used.
It helps ensure appropriate operation of equipment requiring a specific working pressure.
Our selection includes a pressure regulator for Scheppach, Parkside and Zipper compressors, associated with the following references:
These references help identify the component according to the different manufacturer designations.
A faulty regulator may cause unstable outlet pressure, adjustment difficulties or an air leak.
Before ordering a new regulator, it is advisable to check that the problem is not caused by a pressure gauge, fitting or another component of the pneumatic circuit.
The replacement must comply with the pressure specifications and connections intended for the machine.
The pressure switch for Parkside PKO 270 A3 compressor controls automatic motor operation according to the pressure inside the receiver tank.
It normally stops the motor when pressure reaches the threshold specified by the manufacturer and allows it to restart when pressure falls to the designated level.
Our catalogue includes pressure switch reference 3906129013, offered for various Scheppach, Zipper and Parkside compressors.
A faulty pressure switch may cause irregular compressor operation.
Possible symptoms include:
These symptoms alone do not confirm a defective pressure switch. An electrical fault, motor problem or mechanical failure may also be responsible.
The pressure switch is a control and safety-related component that must never be modified or adjusted at random. Replacement should be carried out by a competent person.
Air compressor valves contribute to the operation of certain pneumatic circuits and must perform their intended function according to the machine's configuration.
Our catalogue includes valve reference 5906115043, which replaces the previous reference 5906103043.
This part is offered for various Scheppach, Parkside, Zipper and Woodster compressors, depending on model compatibility.
A damaged valve may interfere with the operation of its pneumatic circuit and cause air losses or pressure-related problems.
Before replacing this component, it is important to identify the exact valve concerned and compare its reference with that of the original part.
This valve should not be confused with the safety valve, which performs a specific protective function against excessive pressure.
The air filter for Parkside PKO 270 A3 compressor helps protect the compression system against dust and airborne particles.
It limits the entry of impurities into the mechanism and contributes to maintaining suitable operating conditions.
Our selection includes an air filter compatible with Parkside PKO 270 A3, PKO 270 A5 and PKO 500 A1 compressors.
This filter is also offered for certain Scheppach HC24(e) and HC50(e) compressors.
It is important to choose the correct filter for your model, as different PKO 270 versions do not necessarily use the same filtration system.
Over time, the filter may become clogged and restrict air intake.
A heavily obstructed filter may contribute to reduced compressor performance.
Regular inspection is recommended, especially when the machine operates in a dusty environment.
A damaged, deformed or excessively dirty filter that cannot be cleaned properly should be replaced according to the manufacturer's recommendations.
The compressor should not be operated without its filter when one is specified by the manufacturer.
The Parkside compressor pressure gauge allows the user to visually monitor air pressure in the section of the circuit where it is installed.
Depending on its position, it may indicate the pressure inside the receiver tank or the pressure available at the regulator outlet.
Our catalogue includes pressure gauge reference 5906102003, offered for various Scheppach and Parkside compressors according to the indicated compatibility information.
Its characteristics include:
A pressure gauge may need replacing if its needle becomes stuck, readings become unreliable or an air leak develops around its connection.
Before ordering, check the diameter, thread, connection position and measuring range of your original gauge.
The Parkside compressor safety valve is an essential device for protecting the compressed air circuit against overpressure.
Our selection includes safety valve reference 5906101094, which replaces the previous reference 5906115059.
This part is offered for various Scheppach, Woodster and Parkside compressors.
A safety valve may need replacing if it shows visible damage, abnormal leakage or a confirmed malfunction.
If it opens repeatedly, the pressure control system must also be checked.
A safety valve must never be blocked, bypassed or modified. The replacement part must comply with the pressure rating and technical specifications specified by the manufacturer.
The compressor gasket support plate is one of the components used in the assembly of certain parts of the compression system.
Our catalogue includes a gasket support plate for various Scheppach, Woodster and Parkside compressors.
This component corresponds to position 48 on certain Scheppach HC50 compressor exploded parts diagrams.
The position number may vary between models. It is therefore essential to compare the part with the exploded diagram corresponding exactly to your compressor.
A damaged or deformed plate may affect the sealing of the relevant assembly.
During maintenance, it is also recommended to inspect the condition of the gaskets and contact surfaces.
The compressor quick coupling allows certain pneumatic accessories to be connected or disconnected conveniently.
It must provide a suitable and sufficiently airtight connection to minimise air losses during operation.
Our catalogue includes a quick coupling for Scheppach, Woodster, Zipper and Parkside compressors.
Depending on the exploded parts diagram, this component may correspond to position 57 or 58.
A quick coupling may need replacing if it develops a persistent leak, mechanical damage or a locking fault.
Before ordering, check the connection type, thread and dimensions of the original part.
The Parkside compressor condensate drain screw allows accumulated water to be drained from the receiver tank according to the manufacturer's instructions.
Our catalogue includes drain screw reference 5906101066, also associated with reference 10003185.
Its stated diameter is 16.6 mm.
This part is offered for various Scheppach, Woodster and Parkside compressors.
A damaged drain screw may cause an air leak or prevent the drain opening from closing correctly.
It is important to check the dimensions and fastening system before ordering.
Condensate should be drained regularly, following the safety and pressure instructions provided in the machine's operating manual.
The Parkside compressor air pipe allows compressed air to flow between the components to which it is connected.
Our selection includes air pipe reference 3906126031, offered for various Parkside compressors according to the compatible machine list.
A damaged pipe may cause an air leak and interfere with the operation of the pneumatic circuit.
Cracks, deformation or deterioration around the connections may require replacement.
Before ordering, it is essential to compare the reference, dimensions and connections with those of the original pipe.
The component must be suitable for the pressure and temperature conditions at its installation location.
Our catalogue also includes a cylinder gasket set intended in particular for the Parkside PKO 270 A5 and Scheppach HC63 compressors.
This set contains gaskets corresponding to positions A 1-5, 1-9, 1-13, 1-25 and 1-26.
Although this reference appears in the compressor spare parts selection, compatibility with the Parkside PKO 270 A3 must not be assumed.
Different PKO 270 versions may have differences in their cylinders, gaskets and mechanical components.
Before ordering, always check the exact machine reference and the compatibility list for the gasket set.
A Parkside PKO 270 A3 compressor that no longer builds pressure may have several different faults.
Worn piston rings can cause a loss of sealing within the compression system and reduce machine performance.
A defective valve, a leaking fitting or a heavily clogged air filter may also interfere with normal operation.
Common symptoms include:
These symptoms can have several causes. An accurate diagnosis is therefore recommended before replacing the piston rings or other components.
A Parkside PKO270A3 compressor that no longer starts may have an electrical, pneumatic or mechanical fault.
The pressure switch may be involved, but it should not be considered defective without appropriate checks.
An electrical supply problem, a faulty capacitor, triggered thermal protection or a blocked mechanism may also prevent the motor from starting.
If the motor makes an unusual noise or appears to struggle without rotating, stop further starting attempts immediately.
Work on electrical components and pressurised parts must be carried out by a qualified person.
Before ordering a replacement part compatible with your Parkside PKO 270 A3 compressor, several checks are recommended.
A visually similar part is not necessarily interchangeable. Differences in dimensions, threads or technical specifications may prevent installation or compromise operating safety.
Regular maintenance helps preserve compressor performance and reduce the risk of certain breakdowns.
It is advisable to periodically inspect the air filter, pneumatic fittings, pressure regulation components and protective devices.
Condensate must be drained according to the operating manual to limit moisture accumulation inside the receiver tank.
Unusual mechanical noises, excessive vibrations and abnormal pressure behaviour should also be monitored.
Before any maintenance operation, disconnect the compressor from the electrical supply, allow it to cool and ensure that the relevant circuits are completely depressurised.
The compressed air receiver tank must never be drilled, welded or repaired using improvised methods. Safety devices must never be bypassed.
Probois Machinoutils specialises in the sale of machinery, workshop equipment, accessories and spare parts for numerous brands.
We offer a developing selection of spare parts for Parkside PKO 270 A3 air compressors to help you maintain and repair your equipment.
Our catalogue includes piston rings reference 39061279004, a pressure regulator, a pressure switch, a valve, an air filter, a pressure gauge, a safety valve, a gasket support plate, a quick coupling, a drain screw and an air pipe.
Part availability may change depending on manufacturer supplies.
Before ordering, carefully read the product descriptions and compare the references with those of your machine.
Whether you are looking for piston rings for Parkside PKO 270 A3, a replacement pressure switch, an air filter, a pressure regulator or a compressor valve, our selection helps you identify the components required to repair your equipment.
By choosing a suitable replacement part and following the manufacturer's recommendations, you can help extend the service life of your Parkside PKO 270 A3 compressor while maintaining its performance.