Spare parts for Leman SRM170 metal band saw

Spare parts for Leman SRM170 metal band saw - Probois Machinoutils

Active filters

Spare parts for the Leman SRM170 metal-cutting band saw

This category covers spare parts for the Leman SRM170 metal-cutting band saw. Unlike a small portable saw, the SRM170 is a workshop machine with a cast-iron frame and saw bow, hydraulically controlled downfeed, bearing blade guides, quick-action vice, gearbox drive and coolant system. Correct operation of these assemblies is essential for accurate and safe cutting.

Our parts range changes with Leman production and availability, so the products currently displayed are not a permanent inventory. The safest identification method is to use the rating plate, exploded parts diagram and item number.

Adjustable hydraulic saw-bow downfeed

The SRM170 features an adjustable hydraulic cylinder controlling saw-bow descent. The bow is raised manually and assisted by an adjustable return spring. During cutting, the hydraulic flow setting controls the downfeed rate and therefore the load applied to the blade.

If the bow drops too quickly, too slowly or irregularly, inspect the adjustment and mechanism before ordering parts. Leakage, loss of holding force and mechanical binding do not necessarily have the same cause. Check pivots, joints and mounting components as well.

Eight-point bearing blade guidance and blade tension

The SRM170 uses adjustable eight-point bearing blade guidance. Play, seized bearings or incorrect adjustment can affect blade stability and cutting accuracy. A wandering cut, however, may also be caused by a blunt blade, unsuitable tooth pitch, incorrect tension, poor work holding or excessive downfeed.

Check blade condition, installation and tension before replacing guides. After any work on the blade or guide system, run the saw briefly without load and observe tracking before making a test cut.

Coaxial gearbox and worm-drive transmission

The drive system uses a coaxial reduction gearbox and worm gear to transmit motor power at the required blade speed. Abnormal noise, excessive play, loss of drive or unusual heating should prompt inspection of the complete mechanical chain rather than immediate replacement of one component.

Before dismantling, make sure the blade and guided mechanisms are not jammed. When servicing the gearbox, retain the original assembly arrangement and follow the manufacturer's lubrication requirements.

Quick-action vice, swivelling bow and length stop

The SRM170 has a quick-action vice with backlash-adjustment lever. Secure work holding is essential because movement can cause blade wander or jamming. Inspect jaws, screw, pivots, lever and sliding components when clamping becomes difficult or inaccurate.

The bow swivels for angled cuts and has a locking mechanism. A work stop is also provided for repeat cuts. If accuracy deteriorates, check these settings and mechanical locks before assuming that the blade guides are faulty.

Coolant system and electric pump

The machine incorporates a coolant system with electric pump and recovery tank. Cutting fluid helps cool the cutting zone and carry swarf away. Loss of coolant flow may result from low fluid level, contamination, a blocked line, a kinked hose, electrical supply problems or pump failure.

Before replacing the pump, inspect the tank, lines and delivery points. Remove accumulated metal chips regularly and use a suitable metal-cutting coolant in accordance with the machine's maintenance instructions.

Electrical controls, safety devices and automatic stop

The SRM170 has 24 V low-voltage controls with an emergency stop, automatic stop at the end of the cut and a safety microswitch on the blade cover. These devices must never be bypassed to work around a fault.

If the saw does not start or stops unexpectedly, first check normal start conditions, guards and accessible safety devices. Electrical faults can have several causes. Internal electrical testing must be carried out with the machine safely isolated by a competent person.

Diagnose the fault before replacing a component

The same symptom can have several causes. A crooked cut does not automatically mean a guide bearing has failed; irregular downfeed does not necessarily identify the hydraulic cylinder; loss of coolant does not always mean the pump is defective.

Inspect the blade, clamping, adjustments, mechanical play, accessible connections and possible swarf blockage. This approach helps replace only the component that is actually faulty and prevents an unresolved cause from damaging the new part.

Identify the correct SRM170 part from the exploded diagram

Leman identifies SRM170 spares using a base reference combined with the exploded-diagram item number. This item number is therefore particularly useful, and Probois product pages for SRM170 parts follow the same principle.

Record the exact machine details from the rating plate. Whenever possible, provide the exploded-view number and clear photographs of the component. Photograph electrical connections before disassembly. Measurements can help with identification but should not replace the manufacturer's reference.

IMPORTANT: check compatibility before purchase

Probois Machinoutils – SEO Leman SRM170 Page 5

IMPORTANT: BEFORE PURCHASING, carefully check the compatible-machine list shown on each product page.

For some parts, the model name alone is not sufficient to guarantee compatibility. Manufacturing changes can result in different components being fitted to machines carrying the same model designation.

If in doubt, send us the exact model, month and year of manufacture and serial number before ordering.

Maintain your Leman SRM170 to reduce breakdowns

Regularly remove swarf from the frame, vice, blade guides and coolant area. Monitor blade condition and tension, guide bearings, hydraulic downfeed and vice clamping. Keep the coolant circuit clean to reduce blockages and contamination.

After repair, perform a no-load test followed by a trial cut with the workpiece securely clamped. Check bow descent, end-of-cut stop, safety devices and any abnormal noise, vibration or heating.

Repair your Leman SRM170 with Probois Machinoutils

Probois Machinoutils offers an evolving range of replacement parts for the Leman SRM170 metal band saw. If the required part is not currently listed, send us the rating-plate details, exploded-diagram item number when known and clear photographs.

Repairing an SRM170 whose frame, bow and main assemblies remain sound can significantly extend its service life. Accurate diagnosis and part identification help preserve cutting capacity, precision and machine safety without replacing equipment that can still be repaired.