Spare parts for Leman SRM150 metal band saw

Spare parts for Leman SRM150 metal band saw - Probois Machinoutils

Spare parts for the Leman SRM150 metal band saw

This category is dedicated to spare parts for the Leman SRM150 metal band saw. The SRM150 is a stationary manual-downfeed metal-cutting band saw with a cast-iron base and saw bow. Its main systems include blade guidance and tensioning, quick-action vice, coaxial gearbox drive, electrical controls and a coolant system. This page is intended to support maintenance and repair without treating the currently displayed parts as a permanent inventory.

Availability changes with Leman production and supply. Identify a requirement by component function, exact machine details and the item number on the exploded diagram. Parts may be added, removed or become available again.

How the Leman SRM150 is built

The SRM150 is a 150 mm manual metal-cutting band saw. The saw bow is lowered by hand with a return spring, can pivot for straight and mitre cuts, and the workpiece is held in a quick-action vice. Blade tension is adjusted by a handwheel and the blade is supported by guide bearings.

This layout differs from portable saws and hydraulic-downfeed machines. SRM100 and SRM170 parts must not be assumed compatible with the SRM150, even when a component looks similar.

Blade guidance, tension and tracking

Accurate cutting requires correct blade tension and stable guidance. Guide bearings, the tensioning mechanism and associated parts all affect blade tracking. Excessive bearing play, seized rotation or wear can reduce accuracy, while incorrect tension can also cause the cut to wander.

Always check the blade before replacing machine parts. A blunt, damaged or unsuitable blade can create the same symptoms. The SRM150 uses a 1735 mm blade, and tooth pitch should suit the material and section being cut.

Coaxial gearbox transmission

The SRM150 uses a coaxial gearbox to transmit and adapt motor movement to the blade drive. New noise, play, irregular drive or loss of movement should prompt inspection of the complete mechanical chain before ordering a component.

If a drive component has failed, investigate the cause. Binding, excessive load or a fault in a neighbouring part can damage the replacement. Also check that the blade moves freely and that swarf is not obstructing the mechanism.

Coolant system and electric pump

The SRM150 includes a coolant system with electric pump and collection tank. Cutting fluid supports the sawing process, so the circuit must remain clean and operational. Loss of coolant flow can result from low fluid level, blockage, displaced hose, an electrical connection or the pump itself.

Before replacing the pump, check fluid level, tank cleanliness, hoses and accessible connections. Metal swarf and deposits can obstruct the circuit. Regular cleaning of the tank and delivery points reduces avoidable faults.

Vice, saw bow, return spring and adjustments

The quick-action vice secures tube, section and other metal workpieces. Poor clamping can cause vibration, movement and blade deviation. Jaws, screws, pivots, handles and adjustment parts should remain in good condition. The saw bow must pivot and descend smoothly.

The return spring assists bow movement. If lowering or return behaviour changes, inspect the complete mechanism before replacing one part. After repair, verify bow movement with the machine switched off before making a test cut.

Electrical controls and safety

The machine uses a low-voltage IP54 switch with emergency stop and trigger operation. If the saw will not start or stops unexpectedly, check the power supply, accessible connections and safety controls before blaming a specific electrical component.

Internal work must be performed with the machine disconnected. Electrical measurements and repairs beyond routine checks should be carried out by a competent person. Replacing a switch or motor from a vague symptom may not solve the actual fault.

Diagnose before replacing parts

A wandering or inaccurate cut can result from a worn blade, unsuitable tooth pitch, incorrect tension, guide play, poor clamping or excessive manual feed pressure. Start with the simplest checks, then inspect guidance, transmission and work holding.

Noise or vibration does not automatically indicate a motor or gearbox failure. Note whether it occurs at no load, during bow movement, under cutting load or only when the coolant system operates. This helps isolate the relevant assembly.

Identify the correct part with the exploded diagram

The safest method is to read the rating plate and use the Leman SRM150 exploded parts diagram. The item number identifies the component within the machine and helps distinguish similar parts. Keep the old part until the replacement arrives so mounting, dimensions and connections can be compared.

When contacting us, provide the rating plate, a clear photo of the component and its item number where possible. For electrical parts, a photo of the original wiring before removal can also help.

IMPORTANT: check compatibility before purchase

Probois Machinoutils - SEO Leman SRM150 Page 5

IMPORTANT: BEFORE PURCHASING, carefully check the list of compatible machines shown on each product page.

For some parts, the model alone is not enough to guarantee compatibility because manufacturers may change components during production.

If in doubt, send us the exact model, month and year of manufacture, and serial number before ordering.

Maintain the SRM150 to extend service life

Regularly remove metal swarf around the blade, guides, vice and accessible mechanisms. Keep the coolant circuit clean, check fluid level and monitor blade condition. A badly worn blade increases cutting effort and unnecessary load on guidance, transmission and motor.

After repair, perform a no-load test followed by a test cut with the workpiece securely clamped. Watch blade travel and coolant flow and listen for abnormal noise or vibration.

Repair your Leman SRM150 with Probois Machinoutils

Probois Machinoutils maintains an evolving selection of replacement parts for the Leman SRM150 metal band saw. If the required part is not displayed, send the rating-plate information, exploded-diagram item number when known and clear photographs.

Repairing a saw whose frame, bow and main assemblies remain serviceable is often more sensible than replacing the complete machine. Correct diagnosis and compatibility checking extend machine life and avoid replacing parts that are still functional.