Spare parts for Leman TAB110 wood lathe
Belt for Leman TAB085 and TAB110 wood lathe
Belt for Leman TAB085 and TAB110 wood lathe
Tailstock spindle for wood lathe Leman TAB110
Tailstock spindle n° 72 for wood lathe Leman TAB110
Shank 25 mm for Robbin type tool holder
25mm shank for the Robbin tool holder suitable for mini wood lathes!
Slide for wood lathe Jean l'ébéniste MC1100B and others
Slider for wood lathe Jean l'ébéniste MC1100B mark 62
Complete slide 10000141 for wood lathe
This slide for tool holders diameter 25.4 mm delivered complete with levers and holding part is dedicated to wood lathes of different brands
Tool Rest Arm for Holzmann VD1100N and Leman TAB110, TAB085 Wood Lathes – Ref. 10004582
Replacement tool rest arm, Holzmann reference 10004582, compatible with Holzmann VD1100N (part no. 58), Leman TAB110 (part no. 69) and Leman TAB085 (part no. 38) wood lathes.
This component is designed to position and support the tool rest during woodturning operations.
Spare parts for Leman TAB110 wood lathe
This category covers spare parts for the Leman TAB110 wood lathe. The floor-standing 230 V machine has a 1100 W S1 motor, 1100 mm between centres, 400 mm swing over the bed and 10 speeds from 500 to 2000 rpm. Its cast construction, swivelling headstock and articulated tool rest make it suitable for varied turning work.
Parts availability changes with production and supply. For reliable identification Leman specifies base spare-parts reference 150100 plus the exploded-view item number. Rating-plate information should also be checked.
M33 x 3.5 spindle and MT2 headstock
The headstock uses an M33 x 3.5 threaded spindle with MT2 taper. Spindle, bearings, pulleys and retaining parts must run without abnormal play or binding.
For vibration, noise or runout, first remove the chuck, faceplate or workpiece and check the bare spindle with the machine unplugged. Poorly mounted accessories can mimic bearing or spindle faults.
Swivelling headstock from 0° to 180°
The TAB110 headstock can be positioned at 0°, 60°, 90°, 120° or 180°. A locking handle and indexing pin secure the selected position.
If movement becomes stiff or the headstock has play after locking, inspect contact surfaces, indexing and clamping components rather than forcing the controls.
Drive belt, pulleys and transmission
A belt transmission connects motor and spindle. Belt, pulleys and related mechanisms transmit the motor power and provide the different operating speeds.
A worn belt may slip, lose drive or create noise. Before replacement check pulley condition, alignment and shaft freedom; rapid belt wear can indicate another fault.
10 stepped speeds without manually moving the belt
TAB110 has 10 speeds: 500, 620, 760, 900, 1050, 1210, 1400, 1590, 1790 and 2000 rpm. Speed changes are made in steps using the control handle, without manually relocating the belt.
If the speed handle becomes stiff or the selected speed behaves incorrectly, inspect the selector mechanism, transmission and pulleys. Always select speed according to workpiece diameter and balance.
MT2 tailstock and bored spindle
The tailstock uses an MT2 taper and has a 10 mm through bore. It slides along the bed and must lock securely for between-centres work and drilling applications.
If the tailstock slips, inspect its bed clamp. If only the quill or handwheel is faulty, diagnose that feed mechanism separately.
300 mm tool rest, articulated arm and banjo
A 300 mm cast-iron tool rest is mounted on an articulated arm with eccentric bed clamping. Tool rest, stem, banjo, arm, handles and clamps must remain rigid in use.
If the support drops or pivots despite tightening, inspect contact surfaces, eccentric parts, shafts and clamping components. Do not compensate for wear by overtightening.
Cast-iron bed and stand
TAB110 uses a cast-iron bed and cast-iron stand to provide stability, particularly with long or large-diameter work.
Strong vibration is not always an internal fault. Check floor stability, stand and bed fasteners, and workpiece balance before replacing spindle or motor parts.
1100 W S1 motor and switch
The machine has a 230 V 1100 W S1 single-phase motor. Switch, power lead, connections and electrical components should be checked if it fails to start or stops unexpectedly.
Begin with supply, plug, cable, switch and mechanical freedom. Internal electrical work must be performed safely with the machine disconnected.
150 mm faceplate, drive centre and live centre
TAB110 is designed for a 150 mm M33 x 3.5 faceplate, MT2 drive centre and MT2 live centre. Accessory condition and mounting can strongly affect running quality.
Before suspecting spindle or bearings, check clean seating, correct fitting and workpiece centring.
Diagnosing vibration or loss of drive
With 1100 mm between centres and a 1100 W motor, significant loads are possible. Vibration can come from imbalance, excessive speed, accessories, clamps, belt, pulley or bearing; loss of drive can originate in the transmission.
Probois Machinoutils – SEO Leman TAB110 Page 5
Remove the work, check accessories and clamps, turn the spindle by hand with power disconnected, then inspect transmission and electrical parts. This helps replace only the genuinely faulty component.
Identify the correct part from the TAB110 exploded diagram
Leman specifies 150100 + exploded-view item number for TAB110 spare-part identification. This is more reliable than visual similarity for shafts, handles, clamps and tailstock components.
If a part is not listed online, send the TAB110 model, rating-plate information, exploded-view item number and clear photographs.
IMPORTANT: check compatibility before purchase
IMPORTANT: BEFORE PURCHASING, carefully check the compatible-machine list on each product page.
Production changes can result in different components. If in doubt send the exact model, month/year of manufacture and serial number before ordering.
Maintain and repair your Leman TAB110
Regularly remove dust and chips around the drive and motor, keep the bed clean, inspect belt, clamps, tailstock and tool-rest rigidity, and monitor spindle play or noise.
Probois Machinoutils offers an evolving range of Leman TAB110 spare parts. Targeted repair can often extend the life of a structurally sound lathe.