Filter By

Brand

Brand

Price

Price

  • €13.00 - €40.00

Availability

Availability

Spare parts for Leman TAB085 wood lathe

Spare parts for Leman TAB085 wood lathe - Probois Machinoutils

Active filters

Spare parts for the Leman TAB085 wood lathe

This category covers spare parts for the Leman TAB085 wood lathe. The 230 V floor-standing lathe uses a 450 W induction motor, offers 850 mm between centres, 305 mm swing over the bed and 10 speeds from 500 to 2000 rpm. Its swivelling headstock also allows suitable outboard turning operations.

Parts availability changes over time. Use the TAB085 model, rating plate and Leman exploded-view item number to identify a component rather than relying only on appearance.

M33 x 3.5 spindle and swivelling headstock

The headstock has an M33 x 3.5 spindle and MT2 taper. The exploded diagram separately identifies the spindle, bearings, pulleys and retaining components.

The head can be positioned at 0°, 60°, 90°, 120° or 180°. If rotation or locking becomes difficult, clean and inspect the positioning and clamping parts before forcing a handle.

Spindle bearings and vibration diagnosis

The Leman parts list includes two 80205Z bearings and a 6006Z bearing in the headstock/transmission assembly.

Noise or vibration does not automatically mean bearing failure. Remove work and accessories, select low speed and check rotation. Poor workpiece centring, excessive speed or loose bed/stand fixing can also cause strong vibration.

Belt, pulleys and transmission

The drive belt links the motor pulleys and spindle pulleys. The diagram shows left/right pulley components on both motor and spindle sides.

Inspect the belt periodically. If the motor runs but the spindle does not, the manual lists a broken belt as a possible cause. Repeated belt wear also calls for checks of pulleys, bearings and alignment.

Speed selector and 10 spindle speeds

TAB085 provides 10 speeds from 500 to 2000 rpm, selected step by step with a lever. The manual instructs the operator to start from the lowest setting and choose a speed appropriate to the work.

If the selector becomes stiff, inspect the mechanism and transmission rather than forcing it. Incorrect or excessive speed can increase vibration.

MT2 tailstock, quill and live centre

The cast-iron tailstock locks to the bed with an eccentric clamp and carries an MT2 live centre. Its quill provides about 50 mm of travel. The exploded view separates tailstock, quill, connecting screw and eccentric clamping parts.

If the tailstock slips, inspect bed clamping; if only the quill binds, inspect its feed mechanism separately.

300 mm tool rest and articulated support

The lathe uses a 300 mm cast-iron tool rest on an articulated support with eccentric clamping, allowing useful positioning for normal and suitable outboard work.

If it moves under load, inspect handle, eccentric shaft, clamping plate, base and contact surfaces. Do not compensate for wear with excessive tightening.

Bed extension and stand

TAB085 has a cast bed, bed extension and steel stand. The extension can support tool-rest positioning for certain headstock orientations.

Strong vibration may simply come from loose bed or stand fixing. Check bolts, braces, supports and floor stability before diagnosing internal parts.

450 W motor, switch and electrical box

The lathe uses a 450 W single-phase induction motor. The parts list includes motor, on/off switch, power lead and electrical box.

If the machine will not start, check supply, lead, plug, switch and mechanical freedom first. Internal electrical work must be performed safely with power disconnected.

Faceplate, drive centre and MT2 accessories

Standard equipment includes an MT2 drive centre, MT2 live centre and 150 mm M33 x 3.5 faceplate. Accessory condition and mounting can strongly affect running quality.

Before replacing spindle or bearings, check that accessories and the workpiece are clean, correctly seated and properly centred.

Diagnose before replacing parts

The TAB085 troubleshooting information distinguishes supply/switch faults, broken drive belt, incorrect speed, excessive speed, poor workpiece centring and loose bed/stand fixing.

Probois Machinoutils – SEO Leman TAB085 Page 5

Check controls, work mounting, speed, hand rotation of the spindle, drive and finally bearings. This helps replace only the genuinely faulty component.

Identify the correct part from the TAB085 exploded diagram

The Leman manual includes a detailed parts list and TAB085 exploded diagram, covering spindle, bearings, pulleys, belt, speed lever, motor, tool rest, tailstock, eccentric clamps and switch.

If a part is not listed online, send the exact model, serial number, manufacturing date if known, exploded-view item number and clear photographs.

IMPORTANT: check compatibility before purchase

IMPORTANT: BEFORE PURCHASING, carefully check the list of compatible machines shown on each product page.

Production changes can result in different components on the same model. If in doubt send the exact model, month/year of manufacture and serial number.

Maintain and repair your Leman TAB085

Regularly clean the bed, controls, adjustment mechanisms and motor ventilation. Inspect belt, moving parts, safety devices and fasteners; lightly lubricate appropriate pivots and sliding parts.

Probois Machinoutils offers an evolving range of Leman TAB085 spare parts. Targeted repair can extend the service life of a structurally sound lathe.