KJD20 switch for different woodworking machines
KJD20 switch for different woodworking machines
KJD20 switch for different woodworking machines
Handwheel fixed headstock bore 19 mm reference 10004481 for mini bench wood lathe
Tool holder clamping device for mini wood lathe
Handwheel reference 10003097 for mini bench wood lathe
Tool Support 150 mm for mini wood lathe
Tool Support 300 mm for mini wood lathe
16mm shank for the Robbin tool holder suitable for mini wood lathes!
This slide for 16 mm diameter tool holders is dedicated to mini wood lathes of different brands
Clamping lever tool holder support for mini wood lathe
This table diameter 150 mm M33 is dedicated to mini wood lathes of different brands
8 mm diameter rod (6 mm tip) for unscrewing the chuck - For mini wood lathe
This category covers spare parts for the Leman TAB040 wood lathe. The compact 230 V lathe uses a 580 W motor and six mechanical speeds from 350 to 3250 rpm. It offers 406 mm between centres and 305 mm swing over the bed. Drive, spindle, headstock, tailstock, tool rest and clamping mechanisms may need servicing over time.
Availability changes with production and supply. For accurate identification Leman specifies base spare-parts reference 150300 plus the corresponding exploded-view item number. Use the rating plate and clear photographs whenever possible.
The headstock transmits rotation to the workpiece. TAB040 has an M33 x 3.5 threaded spindle with MT2 taper. The manual parts list separately identifies the spindle, bearings, indexing components and related hardware.
If the spindle has play, bearing noise or irregular rotation, diagnose it with the machine unplugged and accessories removed. An incorrectly mounted or unbalanced accessory can mimic a spindle fault.
Spindle bearings guide the rotating spindle and directly affect smoothness and turning accuracy. Damage can cause noise, heat, play or vibration that increases with speed.
Before replacing bearings, remove the workpiece and accessories and inspect belt and pulleys. Correct bearing installation is essential to avoid damaging the spindle or new bearing.
TAB040 has no electronic variable-speed drive: its six speeds of 350, 670, 1025, 1500, 2225 and 3250 rpm are selected mechanically through the belt drive. Belt and pulleys are therefore key service parts.
A worn, slack or cracked belt may slip or prevent spindle drive. The manual specifically lists a broken drive belt as a possible cause when the motor runs but the spindle does not. Check pulleys and mechanical freedom too.
The tailstock slides along the bed and supports work between centres. It uses an MT2 taper; the quill has about 65 mm travel and a 10 mm bore. Live centre, quill, threaded rod, handwheel and locks all contribute to accurate positioning.
If the quill binds or will not lock, clean and inspect the mechanism first. Distinguish between movement of the complete tailstock on the bed and movement of the quill itself.
The cast tool rest is positioned through an articulated banjo and eccentric bed clamp. It must remain rigid while turning. Handles, levers, clamping plates and supports are therefore important safety and service components.
If the rest moves during use, inspect the clamp, base and contact surfaces. Do not compensate for a damaged part by excessive tightening.
TAB040 has a 12-position indexing system. It positions the spindle at regular angular intervals for suitable operations with the machine stopped. The manual identifies the indexing/locking lever and indexing gear.
If indexing becomes stiff or inaccurate, inspect alignment and cleanliness rather than forcing it. Do not use the indexing mechanism to resist excessive torque.
The lathe uses a 580 W single-phase 230 V motor. The switch, power lead, connections and motor should be considered if the machine will not start; the manual also provides a wiring diagram.
Start with basic checks: power supply, lead and plug, switch and absence of mechanical seizure. Internal electrical work should only be performed safely by a competent person.
M33 x 3.5 spindle threading and MT2 tapers allow compatible turning accessories to be fitted. The lathe is supplied with a faceplate, drive centre and live centre.
Before suspecting an internal fault, make sure the fitted accessory is clean, correctly seated and compatible. Dirt or imbalance can create runout and vibration.
Vibration can come from an unbalanced workpiece, excessive speed, accessory mounting, belt, pulley or bearing. Loss of drive may be caused by the belt, transmission or a seized spindle.
Work systematically: remove the workpiece, inspect accessories, turn the spindle by hand with power disconnected, then check belt and bearings. This helps replace only the genuinely faulty part.
Probois Machinoutils – SEO Leman TAB040 Page 5
The Leman documentation includes a parts list and exploded diagram. The current spare-parts identification is 150300 + exploded-view item number. This is especially useful for similar screws, shafts, handles and brackets.
If a part is not shown online, send the TAB040 model, rating-plate information, exploded-view item number and clear photographs. Photograph wiring or multi-part assemblies before dismantling.
IMPORTANT: BEFORE PURCHASING, carefully check the list of compatible machines shown on each product page.
For some parts the model alone is not sufficient because production changes may exist. If in doubt send the exact model, month and year of manufacture and serial number before ordering.
Regularly clean the bed, clamping mechanisms and belt-drive area. Monitor belt condition, spindle play, tailstock-quill movement and tool-rest rigidity. Early attention to small faults can prevent further wear.
Probois Machinoutils offers an evolving range of spare parts for the Leman TAB040 wood lathe. Targeted repair can often extend the life of a sound lathe instead of replacing the complete machine.