Belt Poly V 5PJ605 for some planer and thicknesser
Belt poly-V 3PJ605 for some planer and thicknesser
Pair of coals for various small planer jointer machines width 204 mm and 254 mm of the brand Kity, Woodstar and Scheppach or Leman, Fox, etc ...
Set of 2 planer knives for planer and thicknesser Scheppach HMS1070, model with reference 4901204000 and Leman Lodra260
Tensioning mechanism for various small planer jointers
Output table for planer jointer
Single phase Motor 1500W for planer and thicknesseur Leman Lodra 260
Input table for planer jointer Leman LODRA260
Crank for thicknesser Scheppach HMS860 and HMS1080
Drive roller for Leman Lodra 260 thicknesser planer
Iron locking screw for thicknesser planer Scheppach HMS1070 serie 0109 and Leman Lodra 260
Knife protector for Leman Lodra 260 thicknesser planer
Find our selection of spare parts for the Leman LODRA260 planer thicknesser, designed to help you maintain, repair and extend the service life of your woodworking machine.
The Leman LODRA260 is a compact planer thicknesser combining surface planing and thicknessing functions in a single machine. With a planing width of approximately 260 mm, it is suitable for preparing and dimensioning timber in workshops and woodworking applications.
As with any woodworking machine, regular use gradually causes wear to mechanical, electrical and transmission components.
This category brings together replacement parts for the Leman LODRA260 to help restore the machine to proper working condition when a component becomes worn, damaged or defective.
The Leman LODRA260 is fitted with a 1500 W carbon brush motor.
Over time, various components of the electrical system may require inspection or replacement, including the motor, carbon brushes, switches, safety components and associated electrical parts.
A machine that becomes difficult to start, cuts out during operation, loses power or runs irregularly does not necessarily require a complete replacement motor.
The different electrical components and connections should first be inspected to identify the actual cause of the fault before ordering replacement parts.
The drive belts and transmission components of the Leman LODRA260 transfer power from the motor to the different mechanisms of the machine.
Over time, a drive belt can:
stretch;
crack;
become worn;
slip;
lose its grip;
eventually break.
A loose or worn belt can cause poor drive transmission, unusual vibration, abnormal noise or reduced machine performance.
Regular inspection of the drive system can help identify worn components before they cause additional damage.
When operating in thicknessing mode, the Leman LODRA260 uses feed rollers to move the timber automatically through the machine.
The rollers and associated drive mechanism must remain in good condition to ensure smooth and consistent feeding.
A worn roller, damaged spring, loose chain, worn gear or other feed mechanism problem may cause:
irregular timber feeding;
jerky movement;
slipping;
workpiece stoppage;
inconsistent thicknessing results.
This category includes replacement components for maintaining and repairing the feed mechanism of your Leman planer thicknesser.
The Leman LODRA260 uses 2 planer knives measuring 260 × 16.5 × 1.5 mm.
Sharp and correctly adjusted planer knives are essential for obtaining a clean surface while limiting unnecessary strain on the motor and feed system.
Blunt or damaged knives can cause poor surface finish, timber tear-out, increased cutting resistance and excessive load on the machine.
Before purchasing replacement knives, always check their dimensions and configuration against the knives currently fitted to your machine.
The LODRA260 also uses various chains, gears and transmission components to operate its feed system.
These parts are subjected to repeated loads whenever timber passes through the thicknesser.
A loose chain or damaged gear may cause irregular feed movement, noise or loss of drive.
Regular inspection of these components helps identify wear before a minor problem develops into a more serious mechanical failure.
Bearings, shafts, springs, circlips, brackets and other mechanical parts all contribute to the correct operation of the planer thicknesser.
Unusual vibration, excessive play, mechanical noise or irregular movement can indicate that one of these components is worn or damaged.
Replacing the individual faulty component can often restore correct operation without replacing an entire mechanical assembly.
The accuracy of a planer thicknesser also depends on the condition of its adjustment mechanisms and tables.
Handwheels, handles, knobs, shafts, brackets and adjustment components allow the different sections of the machine to be positioned correctly.
A broken component or excessive play in an adjustment mechanism can make accurate setup difficult and may affect the quality of the finished workpiece.
Regular maintenance helps extend the working life of your Leman LODRA260 and reduces the risk of unexpected breakdowns.
We recommend regularly:
checking the condition of the drive belts;
inspecting the feed mechanism;
keeping the planer knives sharp and correctly adjusted;
checking the feed rollers;
removing accumulated chips and dust;
keeping the tables clean;
using suitable dust extraction;
checking for unusual noise or vibration.
Any noticeable change in the way the machine operates should be investigated promptly to prevent a worn component from damaging other parts.
The Leman LODRA260 has an exploded parts diagram with individual reference numbers for its replacement components.
When identifying a spare part, we recommend checking its position and reference number on the machine's exploded diagram before ordering.
The base reference used for spare parts for this machine is 210600, followed by the relevant part identification.
Correct identification is important because components may vary according to the production period or version of the machine.
IMPORTANT: BEFORE PURCHASING, ALWAYS CHECK THE LIST OF COMPATIBLE MACHINES.
Depending on the spare part, the month and year of manufacture and the serial number of your machine may be required to confirm compatibility.
Do not rely solely on the appearance of a component. Check the part reference, dimensions and, where applicable, its position number on the exploded parts diagram.
Motor, carbon brushes, drive belts, feed rollers, chains, gears, bearings, planer knives, switches or adjustment components: find the spare parts for the Leman LODRA260 planer thicknesser you need to maintain and repair your machine.
Selecting the correct replacement part for your model helps extend the service life of your planer thicknesser and maintain good performance for both surface planing and thicknessing operations.
Whether you search for Leman LODRA260 spare parts, planer thicknesser parts or jointer planer replacement parts, carefully checking the machine and part references before ordering will help ensure the correct component is selected.
