Planer wheel for planer jointer Bernardo ADM260 and Jean l'ébéniste ML392
Planer flywheel for planer jointer Bernardo ADM260, Leman RAD250 and Jean l'ébéniste ML392
Planer flywheel for planer jointer Bernardo ADM260, Leman RAD250 and Jean l'ébéniste ML392
Blade clamp in 250 mm for planer thicknesser - Sold individually with the screws
230V switch for Leman RAD250, SRU355 and ASP152 machine
Flywheel for Planer and thicknesser Bernardo FS310P(S) and Holzprofi Maker DR310
Find our selection of spare parts for the Leman RAD250 planer thicknesser, designed for the maintenance, repair and restoration of this 250 mm woodworking machine.
The Leman RAD250 is a combined planer thicknesser that performs two essential woodworking operations: surface planing and thicknessing.
With regular use, some mechanical, electrical and transmission components naturally wear and may eventually need to be replaced.
This category includes a range of replacement parts for the Leman RAD250, helping you repair your machine and extend its working life.
The cutterblock is one of the main components of the planer thicknesser. It holds the knives that remove material during both surface planing and thicknessing.
The Leman RAD250 is equipped with a cutterblock using 3 planer knives measuring 250 × 30 × 3 mm.
The cutterblock assembly also includes various components required to position and secure the knives, such as clamping wedges, screws, springs and other fixing parts.
A damaged component in the cutterblock or knife clamping system can affect the correct positioning and secure mounting of the knives.
Before operating the machine, always make sure that the knives and all their fixing components are correctly installed and securely tightened.
Sharp and correctly adjusted planer knives are essential for maintaining good surface planing and thicknessing performance.
Worn, blunt or damaged knives can cause:
poor surface finish;
timber tear-out;
marks on the workpiece;
increased cutting resistance;
additional strain on the motor;
difficulty feeding timber through the machine.
Before ordering replacement knives for your RAD250, always check their dimensions and mounting system against the knives currently fitted to your machine.
The knife fixing system includes several components that may also need to be replaced over time.
The clamping wedges are used to securely hold the planer knives in the cutterblock.
Springs assist with positioning the knives during installation and adjustment.
Any component that is distorted, broken or has damaged threads should be replaced to ensure that the knives can be correctly and safely installed.
Never operate the planer thicknesser if there is a problem with the knife clamping system.
The Leman RAD250 uses several mechanical components to transfer power from the motor to the cutterblock and feed mechanism.
The pulleys and drive components therefore play an important role in the operation of the machine.
A worn, damaged or misaligned pulley may cause:
vibration;
unusual noise;
poor power transmission;
premature wear of associated components.
When a drive problem occurs, it is advisable to inspect the complete mechanism rather than replacing a component without first identifying the cause of the fault.
During thicknessing, the timber is automatically moved through the machine by feed rollers.
The RAD250 uses a serrated infeed roller and a smooth outfeed roller to provide consistent movement of the workpiece through the thicknesser.
These components must remain in good condition to ensure smooth and regular feeding.
Problems with the feed mechanism may cause:
irregular timber feeding;
jerky movement;
workpiece slipping;
timber becoming stuck;
marks on the workpiece;
inconsistent thicknessing results.
When a feed problem occurs, the rollers should be inspected together with the gears, chains, springs and other components involved in the feed mechanism.
The RAD250 feed system includes various gears, chains and mechanical drive components that transmit movement to the feed rollers.
Over time, a chain may stretch and gear teeth may become worn.
A transmission fault can result in irregular feeding or may completely prevent the machine from feeding the timber.
When carrying out a repair, it is advisable to inspect the entire feed system to ensure that the damaged component is not simply the consequence of another worn part.
The thicknessing table height adjustment handwheel is used to set the final thickness of the workpiece.
This mechanism is regularly operated during normal machine use.
A broken handwheel, damaged handle or adjustment mechanism with excessive play can make it difficult to set the thicknessing height accurately.
The RAD250 also incorporates a system for indicating the thicknessing height.
These components should remain in good condition to make precise machine adjustment easier.
Some faults may also originate from the electrical system.
A faulty switch, damaged connection or another electrical component can prevent the machine from starting or cause unexpected stops during operation.
Before replacing an electrical component, the source of the fault should be correctly identified.
Any work on the electrical system must be carried out with the machine disconnected from the power supply and, if necessary, by a suitably qualified person.
A planer thicknesser contains many smaller parts that are essential to its operation, including bearings, shafts, bushes, springs, screws, pins, circlips and fixing components.
Wear to these parts can cause vibration, excessive play or unusual mechanical noise.
Careful inspection of the machine often makes it possible to identify and replace only the faulty component instead of replacing a complete assembly.
Regular maintenance helps extend the working life of your Leman RAD250 and maintain good machine performance.
It is advisable to:
regularly inspect the planer knives;
check knife adjustment and clamping;
inspect the pulleys and drive system;
check the feed rollers;
inspect the chains and gears in the feed mechanism;
keep the tables clean;
regularly remove wood chips and dust;
use suitable dust extraction;
investigate any unusual noise or vibration.
Acting quickly when a problem first appears can prevent a worn component from damaging other parts of the machine.
The Leman RAD250 has an exploded parts diagram with individual position numbers to help identify its different replacement components.
The base reference used for spare parts for this machine is 210100, combined with the corresponding part number shown on the exploded diagram.
Before placing an order, we therefore recommend locating the required component on the exploded parts diagram.
Also compare:
the shape of the component;
its dimensions;
its mounting system;
its reference number when available;
its position on the exploded diagram.
These checks help reduce the risk of ordering an incorrect spare part.
IMPORTANT: BEFORE PURCHASING, ALWAYS CHECK THE LIST OF COMPATIBLE MACHINES.
Some components used on the Leman RAD250 may also be fitted to woodworking machines from other brands or to models with a similar design.
However, this does not mean that all components are interchangeable.
If there is any doubt, the month and year of manufacture and the serial number of your machine may be required to confirm compatibility.
Do not rely solely on the general appearance of the part. Always compare its dimensions, reference number and position on the exploded parts diagram.
Planer knives, clamping wedges, springs, pulleys, feed rollers, gears, chains, handwheels, switches, bearings, shafts and other components: find the spare parts for Leman RAD250 planer thicknessers you need to maintain and repair your machine.
Replacing a worn or damaged component can often restore an older woodworking machine to proper working condition and significantly extend its service life.
Careful identification using the exploded parts diagram and the specifications of the original component remains the best way to select the correct replacement part for your Leman RAD250.