Mobile head for mini wood lathes Scheppach, Holzmann and Jean l'ébéniste
Potentiometer ref 10000183 for wood lathe Holzmann D460FXL and Jean l'ébéniste MC0430VD
14x9.5 cm electronic board for the Jean l'ébéniste MC0430VD wood lathe variator
Training claw for Kity TAB 660 and Scheppach DM460T
Revolving point for Kity TAB660 and Scheppach DM460T wood lathe and other mini wood lathes (reference 9-11)
Bearing for jean l'ébéniste MC0430VD
Pair of coals for mini wood lathe Jean l'ébéniste MC0430VD and Holzmann D460FXL
KJD20 switch for different woodworking machines
Replacement motor for Holzmann D460FXL and Jean l'ébéniste MC040VD mini wood lathes with variable speed drive
8 mm diameter rod (6 mm tip) for unscrewing the chuck - For mini wood lathe
This category brings together spare parts for Jean l’ébéniste and Holzprofi mini wood lathes. The current range is mainly focused on the Jean l’ébéniste MC0430VD, with several specific electrical and mechanical components. It also includes a belt for the Holzprofi MC1420VF and a number of parts used on various bench-top mini lathes. There are currently twelve products. Always select a component from the compatibility information on its product page rather than from visual similarity alone.
The MC0430VD is the most strongly represented model. Available parts include potentiometer 10000183, a 14 x 9.5 cm speed-controller electronic board, carbon brushes, a replacement motor with a 15 mm shaft, 6005RS bearing item 4 and a 3PJ686 Poly-V belt. These components address different areas of the lathe, so one symptom should never be treated as automatic proof that a particular part has failed.
The potentiometer and speed-controller electronics help regulate motor speed on a variable-speed mini lathe. If speed becomes erratic or the control stops responding normally, the board is not necessarily the only possible cause. The potentiometer, wiring, motor and connections should also be considered. Electrical work must be carried out with the machine disconnected and, where appropriate, by a qualified person.
A replacement motor with 15 mm shaft, carbon brushes and a 6005RS bearing are listed. Brushes are wear parts in a commutator motor; significant wear can affect operation. A worn bearing may develop play, noise or rough running. Noise, vibration or reduced performance can nevertheless have several causes, so inspect associated parts before replacing the motor, bearing or brushes.
The 3PJ686 Poly-V belt is listed for the Jean l’ébéniste MC0430VD and other mini lathes named on its product page. It transfers motion between the machine’s pulleys. Cracking, damage or breakage justify replacement, but unusually rapid wear may indicate pulley, alignment or tension problems. Inspect the surrounding drive before fitting a new belt.
A separate belt is specifically listed for the Holzprofi MC1420VF wood lathe. It must not be confused with the MC0430VD 3PJ686 belt. Two lathe belts can perform the same general function while differing in profile, length and application. Use the exact lathe designation and the individual product information.
The category also contains a tailstock for mini wood lathes, a drive centre and a revolving centre. The tailstock supports accessories and is used to support work between centres. The drive centre transmits rotation to the workpiece, while the revolving centre supports the opposite end and rotates with it. Compatibility with the machine and intended mounting must be confirmed.
A KJD20 switch for various woodworking machines and an 8 mm knockout rod with a 6 mm end are also listed. With switches, external appearance alone is not sufficient: terminals, wiring, electrical ratings and mounting must match. The knockout rod is a mechanical tool for compatible mini lathes and its dimensions should be checked against the machine.
Erratic speed may point toward the speed-control system, but the motor or connections may also be involved. Vibration may originate from a bearing, drive system, incorrectly mounted accessory or even the workpiece. Poor motor operation can justify checking the brushes, but replacing them will not cure an unrelated electronic or mechanical fault. Disconnect the lathe and inspect for play, abnormal heating, damaged cables, belt wear and loose fasteners.
Start with the exact model on the rating plate. MC0430VD parts include identifiable references such as potentiometer 10000183, 6005RS bearing item 4 and belt 3PJ686. Use the manual or exploded diagram when available. Compare dimensions and connections for an electronic board, and mounting details and shaft dimensions for a motor. Do not order solely from a similar-looking photograph.
Regular cleaning and visual inspection make faults easier to detect. Keep dust away from ventilation openings and accessible drive areas, check the belt condition periodically and listen for new bearing or motor noises. Before turning, make sure accessories are correctly seated and locked and that the workpiece is securely mounted. After replacing an electrical or drive component, refit guards and check operation cautiously before returning to normal work. Do not compensate for an unidentified fault by increasing belt tension or continuing to run a motor that is overheating or sparking abnormally.
IMPORTANT: BEFORE PURCHASING, carefully check the compatible machine list on each product page.
For some spare parts, the model alone may not guarantee compatibility because components can change during production.
If in doubt, send us the exact model, month and year of manufacture and serial number before ordering.
Probois Machinoutils is progressively expanding its range of replacement parts for Jean l’ébéniste and Holzprofi mini wood lathes. If the required component is not shown, send the exact model, a photo of the rating plate, photographs of the original part and its exploded-diagram item number where available. Accurate identification helps avoid unsuitable orders and allows the genuinely failed component to be replaced.
