Trapezoidal belt for saw jean l'ébéniste SAF1600i
This category covers spare parts for Jean l’ébéniste and Holzprofi table and sliding table saws that are actually listed in our catalogue. At present, it contains one product specifically for the Jean l’ébéniste SAF1600i: a drive V-belt. The content is therefore deliberately focused on the machine and component currently available rather than suggesting switches, bearings, fences or other parts that are not listed here. The range can be expanded as further verified replacement parts become available.
The SAF1600i is a sliding table saw with a sliding carriage and scoring unit. For this category, “sliding table saw” is more precise than treating it as a basic bench table saw. When looking for a replacement component, identify the SAF1600i designation carefully on the machine. Similar model names or visually similar machines do not prove that parts are interchangeable.
The currently listed component is a V-belt for the Jean l’ébéniste SAF1600i. Probois reference HJCR757-SAF1600 is stated on the product page, together with an inside length of 730 mm. The V-belt forms part of the drive system and transfers motion between the components designed to work with it. Its trapezoidal profile runs in matching pulley grooves. No additional belt dimensions should be inferred where they are not specified on the listing.
Inspect the belt if it is cracked, deformed, frayed, broken or clearly worn. Slipping or irregular drive may also justify checking it. These symptoms do not prove that the belt is the only cause, however. Pulley condition, alignment, belt tension or another part of the mechanism may contribute to the problem. The drive should therefore be inspected as a system before a replacement is ordered.
Replacing a worn belt is most effective when the reason for abnormal wear is also addressed. Incorrect alignment, unsuitable tension or damaged pulley surfaces can shorten belt life. Heavy sawdust deposits can make inspection more difficult and conceal wear. If the old belt is badly damaged, look for uneven wear and inspect the accessible associated components before fitting the new belt.
Disconnect the saw from the power supply before any work and wait until all moving parts have stopped. Note the original belt routing before removal and compare the removed belt with the replacement. Keep the original component until the repair is complete whenever possible. Inspect visible pulley surfaces and remove foreign material from the drive area. After installation, confirm correct belt seating before refitting guards and returning the saw to service.
The current product title refers to “757 mm”, while the technical details state an inside length of 730 mm. This matters because belt sizes may be expressed using different measurement references. Do not compare a single number without knowing what it represents. Use Probois reference HJCR757-SAF1600, the V-belt type, the stated inside length and, above all, the explicit SAF1600i application.
Start with the exact model shown on the saw rating plate. Photograph the plate if useful and retain manufacturing information. If you have a manual or exploded diagram, use it to identify the relevant drive component. A belt that looks similar is not necessarily suitable: profile, length and intended application must match. Avoid choosing a replacement solely from an approximate measurement of a stretched, broken or badly worn belt.
Periodic visual inspection can reveal belt ageing before complete failure. Keep the mechanical area clean, always with the machine disconnected, and watch for rubber dust, cracking or uneven wear. If unusual noise develops, investigate its cause rather than arbitrarily increasing belt tension. Excessive tension can be as undesirable as insufficient tension. Use the machine-specific instructions for any adjustment value or fitting procedure.
A V-belt should always be treated as a machine-specific drive component rather than a generic consumable chosen only by approximate length. The belt profile and effective sizing must suit the pulleys and the intended drive. When an old belt has broken into several pieces, do not assume that measuring one fragment is sufficient. Retain all available pieces, note the machine model and compare them with the product information. If the belt has stretched through age, a direct measurement of the removed part may no longer correspond exactly to the size by which the replacement is identified. This is why the explicit SAF1600i application and product reference are valuable checks. If a newly installed belt immediately runs abnormally, stop the machine and investigate the installation and surrounding mechanism rather than continuing to operate it in the hope that it will settle in.
IMPORTANT: BEFORE PURCHASING, carefully check the list of compatible machines shown on each product page.
For some spare parts, the machine model alone may not guarantee compatibility because components can change during production.
If in doubt, send us the exact model, month and year of manufacture and serial number before ordering.
Probois Machinoutils is progressively developing its range of Jean l’ébéniste and Holzprofi machine spare parts. If another SAF1600i component is required but is not listed here, send us the exact model, rating-plate information, a photograph of the original part and, when available, its item number from the exploded diagram. This approach allows a part to be researched without claiming an unverified compatibility. Replacing the genuinely worn component can extend the service life of a repairable machine.
