Holzmann TS250 Table Saw Spare Parts: Maintain and Repair Your Machine

Are you looking for spare parts for your Holzmann TS250 table saw? At Probois Machinoutils, discover our selection of components and accessories designed to help you maintain your machine, replace worn parts and repair damaged components.

The Holzmann TS250 is a table saw designed for woodworking. It can be used for various cutting operations, including rip cuts and crosscuts, provided that suitable equipment is used and the manufacturer's instructions are followed.

Over time, certain mechanical components may wear out, become misaligned or suffer damage. A deteriorated drive belt, a defective rip fence or an adjustment mechanism that becomes difficult to operate can affect the accuracy and proper functioning of your saw.

Our category includes a 230V replacement motor, a 483J5 Poly-V belt, a motor pulley, a rip fence, a riving knife, a blade guard, adjustment components and sliding table accessories.

Discover the main spare parts available, their functions and the checks you should carry out before ordering.

Which Holzmann TS250 Spare Parts Are Available?

Our selection includes several types of components intended for the maintenance and repair of your table saw.

Motor and drive components

We offer a 230V replacement motor, a motor pulley and a 483J5 Poly-V belt for the Holzmann TS250.

Blade adjustment components

You will find an adjustment handwheel shaft, its corresponding nut, a blade height adjustment handwheel, a saw blade flange and a 5 × 5 × 15 mm key.

Guides and safety devices

Our selection includes a rip fence intended for machines manufactured up to August 2021, a riving knife for machines manufactured from September 2021 onwards, a blade guard and a mitre gauge for a 17 mm T-slot.

Sliding table accessories

We also offer 1000 mm and 1500 mm rails, as well as a sliding table accessory equipped with an extendable fence.

Each component has its own specifications and compatibility requirements.

It is therefore essential to check the information provided on each product page before placing your order.

230V Replacement Motor for Holzmann TS250

The 230V motor for the Holzmann TS250 table saw is one of the machine's main components.

It provides the mechanical power required to drive the cutting system.

A defective motor can cause various symptoms, including starting difficulties, loss of power, irregular operation or unusual noises.

However, these symptoms do not necessarily mean that the motor needs replacing.

An electrical problem, a drive system fault or abnormal mechanical resistance can also interfere with the machine's operation.

Before ordering a replacement motor, it is therefore advisable to carry out an accurate diagnosis.

In particular, check your machine's exact model reference and the specifications of the original motor.

Work on electrical components must be carried out by someone with the necessary qualifications and expertise.

483J5 Poly-V Drive Belt for Holzmann TS250 Table Saw

The 483J5 Poly-V belt for the Holzmann TS250 is an essential component of the drive system.

It transmits movement between the pulleys of the relevant mechanism.

Over time, a belt may wear due to mechanical stress, regular use or unsuitable tension.

A damaged belt can cause irregular power transmission, unusual noises or vibrations.

It is important to inspect its condition during routine maintenance.

When should you replace the 483J5 belt?

Replacement may be necessary when the belt develops cracks, damaged ribs, deformation or significant wear.

Before ordering, always check the markings on your original belt.

The 483J5 designation identifies the standardised characteristics of this Poly-V belt.

Please note that the 483J5 belt intended for the Holzmann TS250 must not be confused with the 406J5 belt offered for the Holzmann TS200.

These are two different references and must not be considered interchangeable.

Motor Pulley for Holzmann TS250

The motor pulley for the Holzmann TS250 forms part of your table saw's drive system.

It transfers movement from the motor to the drive belt.

A pulley in good condition contributes to consistent power transmission, provided that the other components are correctly installed and adjusted.

A damaged pulley may cause premature belt wear or interfere with the proper operation of the mechanism.

Before replacing it, check its condition and the alignment of the entire drive system.

The pulley offered in this category is intended for the Holzmann TS250 and TS200 table saws, as well as the Bernardo TK200, in accordance with the compatibility information provided on its product page.

Always check your machine's exact model reference before ordering.

Holzmann TS250 Rip Fence: Check the Manufacturing Date

The rip fence for the Holzmann TS250 is designed to guide wooden workpieces during rip-cutting operations.

It helps maintain a constant distance between the workpiece and the blade, making it easier to achieve consistent cuts.

A rip fence must be correctly positioned and securely locked before any cutting operation.

If it is bent, damaged or can no longer be secured properly, replacement may be necessary.

Important: The rip fence offered in this category is intended for Holzmann TS250 machines manufactured up to August 2021.

This information is particularly important.

Two machines with the same commercial model name may have technical differences depending on their manufacturing date.

A fence designed for an older version of the TS250 is therefore not necessarily compatible with a newer machine.

Before ordering, check your saw's manufacturing month and year, together with the information provided on the product page.

Riving Knife for Holzmann TS250 Manufactured from September 2021

The riving knife is an essential safety device on a table saw.

It is positioned behind the blade and helps reduce the risk of wood pinching the rear section of the blade.

It therefore contributes to reducing the risk of kickback during certain sawing operations.

To perform its function correctly, the riving knife must be suitable for the machine and compatible with the specifications of the blade being used.

Its thickness, positioning and mounting system are particularly important.

The riving knife offered in this category is intended for Holzmann TS250 machines manufactured from September 2021 onwards.

If your machine was manufactured before this date, do not order this part without first checking its compatibility.

A bent, damaged or unsuitable riving knife must never be used.

Blade Guard for Holzmann TS250 Table Saw

The blade guard for the Holzmann TS250 is designed to cover the upper section of the blade under the operating conditions specified by the manufacturer.

It helps reduce the risk of accidental contact with the rotating blade.

This safety device must be correctly installed and kept in good condition.

A cracked or broken blade guard, or one with damaged mounting components, may need replacing.

Before ordering, check that the proposed model is compatible with your machine and its mounting system.

Never operate your saw with a damaged or incorrectly installed blade guard.

Saw Blade Flange for Holzmann TS250

The saw blade flange for the Holzmann TS250 is a component of the blade mounting system.

It helps secure and position the blade on its shaft.

A damaged, bent or excessively worn flange can affect the correct installation of the blade.

It is therefore important to inspect its condition when replacing the blade or investigating unusual vibrations.

Before carrying out any work, disconnect the machine from the power supply and wait until the cutting system has stopped completely.

During reassembly, follow the manufacturer's instructions regarding the positioning and tightening of the components.

Never use a flange whose specifications do not match your machine.

Blade Height Adjustment Handwheel for Holzmann TS250

The blade height adjustment handwheel for the Holzmann TS250 operates the mechanism used to raise and lower the blade.

This adjustment is essential for adapting the cutting depth to the work being carried out.

A damaged handwheel or one with a deteriorated mounting system may make adjustment difficult.

In some cases, replacing the handwheel alone may be sufficient.

However, if the mechanism jams or develops excessive play, it is also important to inspect the other components of the system.

Our selection includes a shaft and nut for the Holzmann TS250 adjustment mechanism.

Shaft and Nut for the Holzmann TS250 Adjustment Mechanism

The shaft and nut offered in this category form part of the table saw's adjustment mechanism.

These components contribute to the operation of the system controlled by the handwheel.

Over time, threaded components may suffer wear or mechanical damage.

Difficult adjustment, jamming or excessive play may require inspection.

However, these symptoms may also result from sawdust accumulation, misalignment or another component.

Before replacing a part, inspect the entire mechanism.

During installation, follow the manufacturer's recommendations and check that the system operates correctly before putting the machine back into service.

5 × 5 × 15 mm Key for Holzmann TS250

The 5 × 5 × 15 mm key, position B52, is a mechanical component offered for the Holzmann TS250 table saw.

A key is generally used to connect two rotating mechanical components, depending on the design of the mechanism concerned.

Despite its small size, this type of component can play an important role in power transmission.

A bent, worn or damaged key may need replacing.

Before ordering, check its dimensions and position number on your machine's exploded diagram.

Never replace a key with an approximate alternative whose dimensions or specifications do not match those of the original part.

Mitre Gauge for 17 mm T-Slot

The mitre gauge for a 17 mm T-slot is an accessory intended for various compatible woodworking machines.

It can be used on certain table saws, band saws and combination woodworking machines equipped with a suitable slot.

It allows the workpiece to be guided at the required cutting angle, under the operating conditions specified for the machine.

Before ordering, always check the dimensions and profile of the slot in your table.

A similar slot width is not always sufficient to guarantee compatibility.

The proposed mitre gauge corresponds in particular to Scheppach reference 5901309011.

Consult its product page for the list of compatible machines and its exact specifications.

1000 mm and 1500 mm Sliding Table Rails

Our category also includes two rail models intended for the sliding tables of various woodworking machines.

The 1000 mm rail acts as a supporting and guiding component for the corresponding sliding table.

The 1500 mm rail is also designed to guide certain sliding tables fitted to compatible table saws.

A bent or damaged rail may interfere with the movement of the sliding table and affect the consistency of cutting operations.

However, poor sliding movement may also result from rollers, bearings or incorrect adjustment.

Before replacing a rail, it is therefore advisable to inspect the entire guiding system.

Please note that an identical length does not guarantee that two rails are interchangeable.

Always check the dimensions, mounting system and compatibility information for each product.

Sliding Table Accessory with Extendable Fence

We also offer a sliding table accessory equipped with an extendable fence, suitable for various woodworking machines.

This accessory includes a 400 × 250 mm support table, an extendable fence and a screw clamp.

It is intended for certain table saws, spindle moulders and combination woodworking machines from Kity, Scheppach, Woodster, Bernardo and Holzmann.

A sliding table helps guide the workpiece during certain cutting operations.

It can make positioning and securing the wood easier when correctly installed and used with a suitable machine.

Before ordering this accessory for your Holzmann TS250, carefully consult the list of compatible machines and the installation requirements provided on its product page.

Your Holzmann TS250 Will Not Start: Should You Replace the Motor?

A table saw that will not start does not necessarily have a defective motor.

Several components may be responsible for this problem.

Start by checking the electrical supply and control devices without working on live electrical components.

A drive system problem or mechanical blockage may also interfere with the machine's operation.

If the motor makes unusual noises, overheats or suffers a significant loss of power, stop using the machine immediately.

An accurate diagnosis is essential before ordering a replacement motor.

Electrical inspections and repairs must be entrusted to a qualified professional.

Your Holzmann TS250 Vibrates or Makes Noise: Which Parts Should You Check?

Vibrations or unusual noises can have several causes.

A deteriorated drive belt may interfere with the proper operation of the mechanism.

A damaged or misaligned pulley can also cause premature belt wear.

The condition of the blade and its mounting components should also be checked.

A damaged flange or incorrectly installed blade may affect the machine's operation.

It is therefore important to identify the exact cause of the problem before ordering a replacement part.

If significant vibrations or abnormal noises occur, stop the machine immediately and disconnect it from the power supply before carrying out any inspection.

How to Maintain Your Holzmann TS250 Table Saw

Regular maintenance helps preserve the accuracy and proper operation of your table saw.

Before carrying out any work, disconnect the machine from the power supply and wait until the blade has stopped completely.

Regularly clean accessible areas to prevent excessive sawdust and dust accumulation.

Inspect the condition of the blade and its mounting components.

Also check that the rip fence, adjustment mechanism and safety devices are working correctly.

If your machine is equipped with a sliding table, check that it moves smoothly.

Finally, pay attention to unusual noises and any changes in the behaviour of the drive system.

Prompt replacement of a worn or damaged component may help prevent more extensive damage.

How to Identify the Correct Spare Part for Your Holzmann TS250

Before ordering a replacement part, it is essential to identify your machine accurately.

We recommend recording the following information:

• Brand: Holzmann.

• Exact model: TS250.

• Serial number.

• Manufacturing month and year.

• Original part reference, if available.

• Position number on the exploded diagram, where indicated.

Particular attention must be paid to machines manufactured before and from September 2021 onwards.

The rip fence offered in this category is intended for Holzmann TS250 machines manufactured up to August 2021.

The riving knife presented here is intended for machines manufactured from September 2021 onwards.

For the drive belt, always check the 483J5 marking.

For the key, check the 5 × 5 × 15 mm dimensions and position B52.

IMPORTANT: BEFORE PURCHASING, you must check that your machine appears in the LIST OF COMPATIBLE MACHINES provided on the spare part product page. Where necessary, also check your machine's manufacturing month, manufacturing year and serial number.

A component that looks similar to the original part is not necessarily interchangeable.

Why Repair Your Holzmann TS250 Instead of Replacing the Entire Machine?

A localised fault does not necessarily require you to replace your entire table saw.

When a problem originates from a worn belt, a damaged pulley or a component of the adjustment mechanism, replacing the affected part may allow you to repair the machine.

Similarly, a damaged rip fence or handwheel can be replaced independently of the other components, provided that a suitable replacement is available.

Repairing your equipment can therefore extend its service life when its overall condition justifies doing so.

However, an accurate diagnosis remains essential.

Replacing a component that is not responsible for the malfunction will not solve the problem.

For safety devices, only use components suitable for your machine and follow the manufacturer's instructions.

Order Your Holzmann TS250 Spare Parts from Probois Machinoutils

At Probois Machinoutils, discover our selection of spare parts for maintaining and repairing your Holzmann TS250 table saw.

We offer a 230V motor, a 483J5 Poly-V belt, a motor pulley, blade adjustment components, a rip fence, a riving knife, a blade guard and various sliding table accessories.

Before ordering, make sure you identify the exact version of your machine, particularly when compatibility depends on its manufacturing date.

Are you looking for another spare part for your Holzmann TS250?

Send us your machine's exact model, serial number, manufacturing date and, if possible, the position number of the required component on the exploded diagram to help us identify the correct part.

Probois Machinoutils: your specialist in Holzmann machine spare parts, helping you maintain, repair and extend the service life of your TS250 table saw.