Lower guide for metal bandsaw Holzmann BS128HDR/BS115 and Bernardo EBS128C/EBS115
Drive wheel part 35 reference 10009162 for Holzmann BS128HDR and Bernardo EBS128C metal band saws, manufactured before 06/2019
Trapezoidal belt for Holzmann BS128HDR, BS115 after 2015 and Bernardo EBS128C band saws
Bandsaw blade bimetal 1638 mm suitable for different metal bandsaw as Holzmann BS115, Holzmann BS128HDR, Bernardo EBS115
Bandsaw blade bimetal 1638 mm with variable pitch suitable for different metal bandsaw as Holzmann BS115, Holzmann BS128HDR, Bernardo EBS115
Bandsaw blade bimetal 638 mm with variable pitch suitable for different metal bandsaw as Holzmann BS115, Holzmann BS128HDR, Bernardo EBS115
Pinion mark 50 for metal band saw Holzmann BS128HDR and Bernardo EBS128C
230V Motor for metal band saw Holzmann BS128HDR with axis 16.09 mm or manufactured after 2015
Worm shaft ref 10000462 mark 85 for metal band saw BS128HDR and EBS128C
Seal ref 10004499 mark 49 for metal band saw BS128HDR and EBS128C
Hydraulic cylinder for metal band saw Holzmann BS128HDR and Bernardo EBS128C
Handwheel marker 124 for metal band saw Holzmann BS128HDR and Bernardo EBS128C, Holzmann BS115 and Bernardo EBS115
Upper guide for metal bandsaw Holzmann BS128HDR/BS115 and Bernardo EBS128C/EBS115
Motor propeller diameter 24 mm bore 15.5 mm for Holzmann and Bernardo metal bandsaw
Upper drive pulley item number 34 for Holzmann BS128HDR and Bernardo EBS128C metal bandsaws with manufacturing date after 06/2019
Thread bar marker 37 for metal band saw Holzmann BS128HDR/BS115 and Bernardo EBS128C/EBS115
Upper guide for metal bandsaw Jet Promac HVBS-56M
Lower guide for metal bandsaw Jet Promac HVBS-56M
Discover our selection of spare parts for the Holzmann BS128HDR metal bandsaw, designed for the maintenance, repair and restoration of your machine. Replacing a worn or damaged component can extend the service life of your bandsaw and help maintain accurate and consistent cutting performance.
The Holzmann BS128HDR is a metal bandsaw designed for cutting tubes, profiles and various metal workpieces. Its swivelling saw arm allows straight and angled cuts, while the hydraulic lowering system makes it possible to adjust the descent of the saw arm according to the material being cut.
Over time and with regular use, certain mechanical, hydraulic or electrical components may become worn. The drive belt, pulleys, bearings, blade guides, hydraulic cylinder, vice components, switch or blade tensioning mechanism may therefore need to be inspected or replaced.
The Holzmann BS128HDR metal bandsaw consists of numerous components that can be replaced individually. Depending on availability, this category includes various BS128HDR spare parts required for the maintenance and repair of your machine.
Available spare parts may include:
Our range of spare parts for the Holzmann BS128HDR metal bandsaw is regularly updated according to the availability of replacement components from the manufacturer.
The transmission system of the Holzmann BS128HDR drives the bandsaw blade at the speed required for cutting different metals. Several blade speeds can be selected by changing the position of the drive belt on the pulleys.
The Holzmann BS128HDR drive belt is a wear part and should be inspected periodically. A loose, cracked, deformed or damaged belt can cause slipping, loss of drive, vibration or irregular blade operation.
The pulleys and other transmission components should also be checked if unusual noises or drive problems occur. Incorrect alignment or excessive wear can accelerate belt deterioration and affect the correct operation of the machine.
Correct blade guidance plays an essential role in the cutting accuracy of the Holzmann BS128HDR metal bandsaw. The bearing-guided system keeps the bandsaw blade correctly positioned during cutting.
The bearings and other blade guide components are subjected to significant loads during operation. With regular use, they may develop excessive play, become noisy or no longer guide the blade correctly.
Worn or incorrectly adjusted BS128HDR blade guides can contribute to irregular cuts, blade deviation or vibration. Their condition and adjustment should therefore be checked before automatically assuming that the bandsaw blade itself is responsible for poor cutting performance.
The Holzmann BS128HDR features a hydraulic saw arm lowering system. This system allows the lowering rate of the saw arm to be adjusted according to the material and the cross-section of the workpiece being cut.
The hydraulic cylinder and its associated components directly contribute to the smooth and controlled descent of the saw arm. If the arm lowers too quickly, moves irregularly or becomes difficult to adjust, the hydraulic system should be inspected.
A worn or faulty BS128HDR hydraulic cylinder can affect control of the saw arm and consequently the quality of the cut. The mounting and adjustment components associated with the cylinder should also be checked if a problem occurs.
Correct blade tension is essential for achieving consistent and accurate cuts. A blade that is not sufficiently tensioned may deviate during cutting, while excessive tension can place unnecessary stress on the blade, bearings, band wheels and other mechanical components.
The blade tensioning mechanism consists of several parts that can become worn or damaged. The tensioning handle, shafts, screws and associated components should be inspected if the blade can no longer be tensioned correctly.
A blade that starts to wander does not necessarily mean that the blade itself is defective. Blade tension, guide adjustment, bearing condition and workpiece clamping should also be checked.
The Holzmann BS128HDR features a clamping system designed to hold the metal workpiece securely during cutting. Correct workpiece clamping is essential for consistent cutting and helps prevent the material from moving while the machine is operating.
The clamping screw, movable jaw, crank handle, shafts and other vice components are regularly subjected to mechanical stress. Wear in these parts can result in excessive play or make it more difficult to clamp the workpiece securely.
A correctly functioning metal bandsaw vice contributes directly to cutting accuracy and safe operation.
The design of the Holzmann BS128HDR allows the saw unit to swivel for different angled cuts. The pivot mechanism, locking components and associated parts must remain correctly adjusted to maintain the accuracy of the machine.
If the cutting angle becomes difficult to adjust or lock securely, the shafts, locking mechanisms, adjustment components and other parts involved in the saw arm pivoting system should be inspected.
Replacing a worn Holzmann BS128HDR saw arm adjustment component may be necessary if excessive play develops or if the locking mechanism becomes damaged.
The Holzmann BS128HDR features an automatic shut-off system at the end of the cut. When the saw arm reaches its lower position, the mechanism operates the control system to stop the machine.
The mechanical and electrical components involved in this system must remain correctly adjusted and in good condition. If the automatic shut-off system does not operate correctly, the relevant components should be inspected before the machine is returned to service.
The electrical system of the bandsaw includes various components required for controlling and operating the machine. A damaged switch or faulty electrical component may prevent the bandsaw from starting or cause abnormal operation.
The Holzmann BS128HDR is available in different electrical versions, including 230 V and 400 V. It is therefore essential to check the exact voltage of your machine before ordering a motor, switch or other electrical component.
Before ordering an electrical spare part for the Holzmann BS128HDR, compare the specifications of the original component with the information shown on the machine identification plate.
Before carrying out any work on the electrical system, completely disconnect the machine from the power supply. Electrical repairs requiring specific expertise should be carried out by a suitably qualified person.
Regular maintenance helps extend the service life of your bandsaw and reduce premature component wear. Metal chips should be regularly removed from around the blade guides, band wheels, vice and other moving components.
Periodically check the blade tension and condition, blade guides, bearings, drive belt, pulleys, hydraulic cylinder and clamping system. Any excessive play, unusual noise or abnormal operation should be investigated before continuing to use the machine.
Irregular or wandering cuts can have several causes: a worn or unsuitable blade, incorrectly adjusted blade guides, worn bearings, incorrect blade tension, incorrect saw arm lowering adjustment or inadequate workpiece clamping.
Regular inspection of the wear parts on the Holzmann BS128HDR can help identify a faulty component before it causes additional wear or damage to other parts of the machine.
The blade is one of the main consumable parts of a metal bandsaw. The blade tooth pitch should be selected according to the material, shape and thickness of the workpiece being cut.
A worn or damaged blade, or a blade with an unsuitable tooth pitch, can result in slow, irregular or inaccurate cutting. Before replacing the blade, it is also advisable to check the blade guides, bearings and tension to ensure that the machine is correctly adjusted.
When purchasing a bandsaw blade for the Holzmann BS128HDR, always check the required blade dimensions and select a tooth pitch suitable for your application.
Before ordering a spare part for your Holzmann BS128HDR metal bandsaw, consult the exploded diagram and spare parts list corresponding to your machine to accurately identify the required component and its position number.
This check is particularly important for electrical components, transmission parts, hydraulic components and blade guide parts. Some part references may have changed depending on the production period or version of the machine.
IMPORTANT: BEFORE PURCHASING, always check the LIST OF COMPATIBLE MACHINES shown on the spare part product page. Depending on the component, you may also need to check the month and year of manufacture and the serial number of your machine.
Not all spare parts for the Holzmann BS128HDR metal bandsaw are necessarily listed in our online catalogue. If you cannot find the component you need, consult the exploded diagram of your machine to identify its position number.
To help identify the correct spare part, provide the exact model of your bandsaw, its supply voltage, serial number, manufacturing date and the position number of the required component.
A photograph of the original component together with its main dimensions can also help with identification when a part number has changed or when several versions exist.
A worn drive belt, faulty bearing, damaged blade guide, hydraulic cylinder problem, vice component, switch or blade tensioning component does not necessarily mean that the complete bandsaw needs to be replaced.
Many mechanical, hydraulic and electrical components can be replaced individually to repair your Holzmann BS128HDR metal bandsaw, restore correct operation and extend its service life.
Probois Machinoutils offers a constantly evolving range of spare parts for Holzmann metal bandsaws to help with the maintenance, repair and restoration of your machines.
Browse our Holzmann BS128HDR spare parts and use the exploded diagram together with the information shown on your machine to accurately identify the replacement part you need.
Remove unsupported machine detailsReduce repetitive SEO wording
