Jet Drum Sanders Spare Parts

Jet Drum Sander Spare Parts | Conveyor Belts and Replacement Parts

Active filters

Roller Bushing for JET Drum Sander

19,99 € Tax included

Roller bushing for JET JWDS-1020, JWDS-1632, JWDS-1836, JWDS-2244 and JWDS-2244OSC drum sanders. Replacement spare part for roller guidance and support.

Drive Roller for Jet JWDS-1632 Drum Sander – Part No. 25

79,99 € Tax included

Replacement drive roller for the Jet JWDS-1632 drum sander, corresponding to position 25 in the exploded parts diagram.

This component helps ensure consistent feeding of wooden workpieces through the sanding machine, contributing to smooth operation and uniform sanding results.

Drive Conveyor Belt for Jet JWDS-1020 Drum Sander

109,99 € Tax included

Drive conveyor belt for Jet JWDS-1020 drum sander.
Dimensions: 250 x 826 mm. This conveyor belt ensures smooth and consistent feeding of wood through the sanding drum, helping to achieve accurate thickness sanding and a high-quality finish. An ideal replacement part when the original belt becomes worn, damaged, or loses grip.

Drive Conveyor Belt for Jet JWDS-1632 and JWDS-1836 Drum Sanders

142,99 € Tax included

Drive conveyor belt for Jet JWDS-1632 and Jet JWDS-1836 drum sanders.
Dimensions: 970 x 442 mm. This conveyor belt ensures smooth and consistent feeding of wood through the sanding drum, helping to achieve accurate thickness sanding and a high-quality finish. An ideal replacement part when the original belt becomes worn, damaged, or loses grip

JET Drum Sander Spare Parts: Maintenance, Repairs and Sanding Consumables

A JET drum sander is a valuable woodworking machine for sanding timber surfaces, preparing panels and achieving a consistent finish on workpieces of relatively uniform thickness. Used in joinery, cabinetmaking and furniture workshops, it allows precise surface sanding on different types of timber, within the operating limits of each machine.

To maintain consistent results and extend the service life of your equipment, it is important to monitor the condition of the sanding abrasives, conveyor belt and adjustment mechanisms. Certain components are subject to gradual wear and must be replaced when they no longer perform their intended function correctly.

At Probois Machinoutils, we offer a selection of JET drum sander spare parts, accessories and consumables for maintaining several models from the JET range.

This category includes conveyor belts for JET drum sanders, abrasive sanding rolls, table extensions, adjustment components and guiding parts. Every replacement component must be selected according to the exact model of your machine.

Conveyor Belt and Feed Belt for JET Drum Sander

The conveyor belt on a drum sander plays an essential role in moving timber beneath the abrasive sanding drum. It helps maintain a consistent feed rate throughout the sanding process and contributes to an even finish across the workpiece.

With repeated use, the conveyor belt surface may lose its grip, become damaged or develop tears. A worn feed belt can cause irregular movement of the workpiece, marks on the timber or feeding difficulties.

We offer a replacement conveyor belt for the JET JWDS-1020, measuring 250 x 826 mm, designed to replace the feed belt fitted to this model.

Another conveyor belt for the JET JWDS-1632 and JWDS-1836, measuring 970 x 442 mm, is available for these two machines.

These references must not be confused, as conveyor belt dimensions vary between drum sander models. Before ordering, check the exact designation of your equipment and the compatibility information provided on the product page.

How to Recognise a Worn Drum Sander Conveyor Belt

A JET drum sander feed belt may show several signs of wear. A smooth or damaged surface, tears, deformation or difficulty moving timber consistently should prompt a closer inspection.

When a workpiece moves unevenly or in jerks, the problem may also be caused by incorrect belt tension, tracking problems or another component within the conveyor drive mechanism.

Before replacing the belt, it is therefore advisable to inspect its overall condition and check the adjustments specified by the manufacturer.

After fitting a new conveyor belt, its tension and tracking must be adjusted according to the machine's instruction manual. An incorrectly positioned belt may move sideways and suffer premature wear.

Abrasive Sanding Rolls for JET Drum Sanders

Abrasives for JET drum sanders are essential consumables for the correct operation of these machines. They remove material from the workpiece and help prepare timber surfaces for subsequent finishing operations.

In this category, we offer 75 mm wide abrasive rolls in lengths of 12.5 metres and 25 metres, together with 86 mm wide rolls measuring 25 metres in length for the JET JWDS-1836.

The 75 mm abrasive rolls supplied in 12.5 metre lengths can be used to prepare up to five sanding strips, with angled cuts suitable for fitting around the sanding drum.

The width and length of the abrasive must correspond to the requirements of the machine concerned. It is also essential to follow the manufacturer's instructions regarding the cutting shape and installation method.

An incorrectly fitted abrasive strip can produce an uneven sanding finish, cause premature wear or create operating difficulties.

Which Abrasive Grit Should You Choose for a JET Drum Sander?

Choosing the correct abrasive grit for a drum sander depends on the initial condition of the timber, the amount of material to be removed and the desired surface finish.

Our selection includes the following grit sizes:

  • 60 grit: suitable for initial sanding passes and surfaces requiring more substantial material removal.
  • 80 grit: designed for intermediate sanding and preparing workpieces that still have surface irregularities.
  • 120 grit: useful for refining the surface after an initial sanding operation.
  • 180 grit: intended for finishing passes when the condition of the timber and the required result allow it.

It is generally advisable to progress from a relatively coarse abrasive to a finer grit without making excessively large jumps between sanding stages.

The amount of material removed during each pass must remain suitable for the machine's capabilities, the timber species and the abrasive grit being used. An excessively deep pass may cause overheating, overload the machine or leave unwanted marks on the surface.

When sanding softwoods and timber species that tend to clog abrasives quickly, it is particularly important to monitor the condition of the sanding strip and adjust the sanding settings accordingly.

86 mm Abrasive Rolls for JET JWDS-1836 Drum Sander

For the JET JWDS-1836, our catalogue includes a dedicated selection of 86 mm wide abrasive rolls, supplied in lengths of 25 metres.

These abrasives are available in 60, 80, 120 and 180 grit, covering different stages of sanding, from initial surface preparation to finishing work.

The rolls can be cut into the sanding strips required to wrap around the sanding drum. The angled ends must be cut to suit the machine's fixing system and ensure correct installation.

It should not be assumed that an abrasive roll intended for one drum sander model will automatically fit every other JET machine. Dimensions and fixing requirements must always be checked.

Table Extensions for JET Drum Sanders

JET drum sander table extensions are useful accessories for improving support at the infeed and outfeed sides of the machine.

They are particularly helpful when sanding panels, long boards, shelves and components intended for furniture manufacturing.

Our catalogue includes a set of table extensions for the JET JWDS-2244, as well as a table extension set for the JET JWDS-1632 and JWDS-1836.

These accessories make workpieces easier to handle and provide additional support as timber passes through the sander. However, they do not replace the additional support equipment required for particularly long or heavy workpieces.

Before ordering table extensions, check their compatibility with your machine and follow the manufacturer's installation instructions.

Conveyor Adjustment Handle for JET DDS-225 and DDS-237

The correct operation of the conveyor system also depends on the adjustment devices used to set the feed mechanism.

We offer a conveyor adjustment handle for the JET DDS-225 and DDS-237 drum sanders, corresponding to position 12 in the technical documentation.

This component is intended for the models specified on its product page and can be used to replace a damaged or unusable adjustment handle.

A broken or deteriorated handle can make it difficult to adjust the relevant mechanism. It is important to replace this component with a suitable part rather than using an improvised solution.

Before carrying out any work, consult your drum sander's exploded parts diagram to confirm the component's position and installation.

Roller Bush for JET JWDS Drum Sanders

Among the mechanical components available is a roller bush for JET drum sanders, designed to contribute to the guidance and support of the roller assembly.

This component is listed for several machines in the range: JET JWDS-1020, JWDS-1632, JWDS-1836, JWDS-2244 and JWDS-2244OSC.

A worn or damaged guiding component may cause incorrect positioning of the relevant mechanical assembly. However, operating problems can have several causes and should be investigated before replacing a part.

To identify the correct replacement bush, check your drum sander model and the compatibility information provided on the product page.

Spare Parts for JET JWDS-1020, JWDS-1632, JWDS-1836 and JWDS-2244

JET JWDS drum sanders are available in different sizes and configurations. Although their operating principles are similar, their components are not necessarily interchangeable.

The JET JWDS-1020 uses a specific conveyor belt. The JET JWDS-1632 and JWDS-1836 share certain references in our catalogue, including a replacement conveyor belt and a set of table extensions.

The JET JWDS-2244 has its own dedicated table extension set. Several JWDS models are also covered by the replacement roller bush available in this category.

For the JET DDS-225 and DDS-237, our range includes a conveyor adjustment handle.

It is therefore essential to search for spare parts using the exact machine model rather than relying solely on a component's appearance or function.

How to Identify the Correct Spare Part for Your JET Drum Sander

Before ordering a replacement part for a JET drum sander, we recommend recording the information shown on your machine's identification plate.

To reduce the risk of ordering the wrong component, follow these steps:

  • Identify the complete model designation of your JET drum sander.
  • Check the serial number if several versions of the machine exist.
  • Consult the instruction manual and exploded parts diagram for your model.
  • Locate the position number of the component requiring replacement.
  • Compare its dimensions and part number with the information in our catalogue.
  • Check the width and length when ordering conveyor belts and abrasive rolls.
  • Contact our team if you are unsure about compatibility.

This procedure is particularly important for drive components, adjustment mechanisms and table accessories.

Maintaining Your JET Drum Sander for Consistent Sanding Results

A JET drum sander requires regular maintenance to preserve its performance and limit premature wear of its components.

After each use, it is advisable to remove accumulated dust from accessible areas and check the condition of the dust extraction system. Fine dust produced during sanding can accumulate around mechanisms and interfere with their operation.

The conveyor belt must remain clean and correctly adjusted. Its surface condition, tension and tracking should be checked according to the manufacturer's recommendations.

It is also important to monitor abrasive wear. A clogged or damaged sanding strip may cause surface marks, excessive heat or a reduction in sanding quality.

Before cleaning, adjusting or replacing any component, the machine must be switched off and disconnected from its electrical power supply.

Finally, adjustment mechanisms and safety devices must be kept in good condition. Any mechanical or electrical fault should be identified before the machine is returned to service.

Why Buy JET Drum Sander Spare Parts from Probois Machinoutils?

At Probois Machinoutils, we help professional woodworkers and DIY enthusiasts maintain and repair their woodworking machinery.

Our selection of JET drum sander spare parts and consumables includes conveyor belts, abrasive rolls in different grit sizes, table extensions, adjustment components and guiding parts.

We provide information about compatible models and relevant technical specifications to make replacement components easier to identify.

If you are looking for a part that is not listed in our catalogue, you can send us the complete reference of your machine together with the position number of the component shown on its exploded parts diagram. This information will allow us to review your request and, where possible, help you find a suitable solution.

Discover JET drum sander spare parts, conveyor belts, table extensions and sanding abrasives at Probois Machinoutils to maintain your equipment and preserve the quality of your woodworking projects.