Support sticker 300 mm to mount abrasive disc hook and loop
Discover our selection of spare parts and accessories for Holzmann TSM250 and TS305 disc sanders, two stationary sanding machines designed for sanding, shaping, adjusting and finishing wooden workpieces.
A disc sander is particularly useful for sanding edges, adjusting the ends of workpieces, correcting small surface irregularities and producing accurate finishes.
It is a practical piece of equipment for woodworking workshops, joineries, cabinetmakers and DIY enthusiasts who regularly work with wood.
Over time, certain components may wear out or become damaged. Sanding abrasives must also be replaced regularly to maintain efficient sanding performance.
At Probois Machinoutils, we offer replacement parts to help you maintain your machine, replace damaged accessories and extend the service life of your equipment.
This category is specifically dedicated to the Holzmann TSM250 and Holzmann TS305 models.
Before ordering, always check the compatibility information provided on the individual spare part listing.
The Holzmann TSM250 is a stationary disc sander equipped with a 250 mm diameter sanding disc.
It is designed for various sanding and finishing operations, particularly on the edges and ends of wooden workpieces.
To maintain good performance, it is important to regularly inspect the condition of the sanding disc, backing plate and other machine components.
A worn abrasive disc can reduce sanding efficiency, while a damaged backing surface may affect the secure attachment of the abrasive.
Replacement parts for the Holzmann TSM250 must be selected according to the exact specifications of the machine.
Important: accessories designed for the Holzmann TS305 are not automatically compatible with the TSM250.
The Holzmann TS305 is a stationary disc sander equipped with a 305 mm diameter sanding disc.
It features a 750 W motor and a worktable that can be tilted up to 45°, allowing various sanding and adjustment operations.
Its large sanding disc provides a useful working surface for sanding edges, shaping workpieces and achieving accurate finishes.
As with any stationary sanding machine, performance depends on the condition of the abrasives and the proper operation of its mechanical components.
Replacing a damaged backing pad or defective component can help restore satisfactory working conditions without replacing the entire machine.
Before ordering a spare part for the TS305, check its dimensions, attachment system and reference number.
Among the accessories available in this category, you can find a 300 mm diameter self-adhesive hook-and-loop backing pad, designed for use with compatible hook-and-loop sanding discs.
This type of backing pad is attached to a suitable sanding plate and creates a hook-and-loop surface that holds the abrasive disc in place.
The hook-and-loop system offers a practical advantage: it makes abrasive replacement easier and allows users to quickly change between different grit sizes according to the work being performed.
It therefore becomes easier to switch from coarse sanding to finer finishing.
This system can be particularly useful for users who regularly alternate between several abrasive grits.
Before choosing a hook-and-loop backing pad, always check:
The diameter of your sander's plate.
The exact diameter of the backing pad.
The existing attachment system.
The dimensions of the sanding discs used.
The compatible machine list provided on the product page.
A 300 mm backing pad must never be considered compatible with a 250 mm disc sander without checking the specifications first.
The backing pad plays an essential role in securing the sanding disc.
When it becomes worn, damaged or partially detached, it may no longer hold the abrasive correctly.
Several warning signs may indicate that replacement is necessary:
The sanding disc no longer adheres properly.
The hook-and-loop surface is damaged.
The backing pad is beginning to peel away.
Changing sanding discs becomes difficult.
The abrasive no longer remains securely attached.
A damaged backing pad can affect sanding quality and create a safety risk during operation.
It is therefore important to inspect its condition regularly and replace it when necessary.
Before carrying out any maintenance or replacement, disconnect the sander from the power supply and wait until the sanding disc has come to a complete stop.
Regular maintenance helps preserve the performance and service life of your Holzmann TSM250 or TS305 disc sander.
Sanding dust can accumulate on the worktable, around the sanding plate and in other areas of the machine.
Accessible surfaces should be cleaned regularly in accordance with the manufacturer's instructions.
The condition of the sanding disc should also be checked frequently.
A clogged, torn or excessively worn abrasive disc should be replaced to maintain effective sanding performance.
Also inspect the worktable, adjustment mechanisms and fastening components.
If unusual vibrations, abnormal noises or operating problems occur, stop the machine immediately and identify the cause before using it again.
The main difference to consider when selecting sanding discs and backing pads is the sanding disc diameter.
Holzmann TSM250: 250 mm sanding disc diameter.
Holzmann TS305: 305 mm sanding disc diameter.
This difference is essential when selecting a suitable sanding disc or backing pad.
An accessory designed for a 305 mm sanding plate must not be considered interchangeable with an accessory intended for a 250 mm plate.
Likewise, mechanical components, electrical parts and fastening elements may vary depending on the model and manufacturing period.
Compatibility must therefore always be checked individually.
Before ordering a replacement part for your disc sander, start by identifying the exact model of your machine.
Check whether the identification plate indicates TSM250 or TS305.
Next, verify the description, dimensions and technical specifications of the component you need.
For certain replacement parts, consulting the machine's exploded diagram may be necessary to identify the corresponding part number.
Two components may look almost identical while having different dimensions or attachment systems.
For this reason, we strongly recommend that you do not select a replacement part based solely on its photograph.
IMPORTANT: BEFORE PURCHASING, always check that your machine appears in the list of compatible machines provided on the spare part's product page. Where necessary, also verify the month and year of manufacture and your machine's serial number.
A malfunction or worn accessory does not necessarily mean that your disc sander needs to be replaced.
When the problem has been correctly identified and the appropriate replacement part is available, repairing the machine can help extend its service life.
Replacing a damaged hook-and-loop backing pad, worn accessory or defective component may be an appropriate solution.
However, it is essential to select the correct reference and follow the manufacturer's recommendations.
Complex electrical or mechanical repairs should only be carried out by suitably qualified individuals.
At Probois Machinoutils, we are continuously developing our range of spare parts for woodworking and metalworking machines.
This category is specifically dedicated to the Holzmann TSM250 and TS305 disc sanders and may be expanded with additional references according to availability.
If you cannot find the part you need, please provide the exact model of your machine, its serial number and, if possible, the reference number shown on the exploded parts diagram.
A photograph of the original component may also help us identify the correct replacement.
Whether you are looking for a hook-and-loop backing pad for a Holzmann disc sander, a sanding accessory or a replacement component, explore our selection and carefully check compatibility before placing your order.
