Pebble rep 29 for Scheppach BTS700 belt and disc sander
Pebble rep 29 for Scheppach BTS700 belt and disc sander
Pebble rep 29 for Scheppach BTS700 belt and disc sander
Belt protection piece item 26 for Scheppach, Woodstar and Manupro belt and bench disc sander
Motor for belt and disc sander Scheppach BTS700, BD7500, Woodster BD75, Mac Allister MBDP250MAC
Angle guide for belt sander and bench disc Scheppach, Woodstar and Manupro
Belt side work table mark 41 for Scheppach, Woodstar and Manupro belt and bench disc sander
Disc suction cover item 56 for Scheppach, Woodstar and Manupro belt and bench disc sander
Drive wheel item 36 for Scheppach, Woodstar and Manupro bench-top belt and disc sander
Disk tray mark 70 for belt sander and bench disk Scheppach, Woodstar and Manupro
Mark 22 sanding mat for belt and bench disc sander Scheppach, Woodstar and Manupro
Rubber foot for belt and bench disc sander Scheppach, Woodstar and Manupro (sold individually)
Protective cover mark 27 of the abrasive belt for belt sander and bench disc Scheppach, Woodstar and Manupro
Capacitor 8µF 400V for belt sander and bench disc Scheppach, Woodstar and Manupro
Start-up relay for belt and disc sander Scheppach BTS900X, Scheppach BTS800 and Kity PBD900
KJD20 switch for different woodworking machines
Abrasive belt 25x762 mm grit 80 for belt and disc sanding machines as Kity PBD700, Scheppach BD7500, Scheppach BTS700, Holzmann BT75, OTMT, Mac Allister MBDP250
Abrasive belt 25x762 mm grit 120 for belt and disc sanding machines as Kity PBD700, Scheppach BD7500, Scheppach BTS700, Holzmann BT75, OTMT, Mac Allister MBDP250
Hook and Loop abrasive disc diameter 125 mm grit 60 for sander polishers, orbital sander
Hook and Loop abrasive disc diameter 125 mm grit 120 for sander polishers, orbital sander
Abrasive belt 25x762 mm grit 240 for belt and disc sanding machines as Kity PBD700, Scheppach BD7500, Scheppach BTS700, Holzmann BT75, OTMT, Mac Allister MBDP250
Discover our selection of spare parts for the Mac Allister MBDP250MAC belt and disc sander, designed to help you repair, maintain and extend the service life of your woodworking machine. This compact benchtop sander combines a sanding belt and a sanding disc, making it suitable for shaping, smoothing and finishing wooden components.
Thanks to its two sanding systems, the Mac Allister MBDP250MAC can be used for a wide variety of woodworking applications, including sanding flat surfaces, finishing edges, adjusting angles and working on smaller wooden pieces.
Over time, regular use, mechanical wear or accidental damage may cause certain components to deteriorate or require replacement. At Probois Machinoutils, we offer a selection of compatible replacement parts to help you restore your Mac Allister sander to proper working condition.
Whether you need a replacement motor, a new switch, a mechanical component or a sanding accessory, choosing a part compatible with the exact model of your machine is essential.
The Mac Allister MBDP250MAC is a benchtop woodworking machine combining a belt sander and a disc sander in a single compact unit.
The sanding belt is particularly useful for smoothing edges, shaping small wooden components and finishing surfaces. The sanding disc is ideal for adjusting workpiece ends, sanding angles and producing accurate finishes on smaller pieces.
This type of combined sander is commonly used by DIY enthusiasts, hobby woodworkers and carpenters for furniture making, restoration projects and general workshop finishing tasks.
To maintain consistent sanding performance, it is important to regularly inspect the condition of the abrasives, motor, guiding components and safety devices.
Using correctly sized sanding belts and discs also helps reduce unnecessary mechanical stress and maintain accurate sanding results.
The Mac Allister MBDP250MAC sander motor is one of the machine's most important components. It provides the power required to drive the sanding belt and disc during operation.
After several years of use, an electric motor may show signs of wear or develop an electrical or mechanical fault. A machine that no longer starts, stops unexpectedly or produces unusual noises should be inspected before being used again.
Depending on the cause of the problem, replacing the motor may allow the sander to be repaired without purchasing an entirely new machine.
At Probois Machinoutils, we offer a replacement motor compatible with the Mac Allister MBDP250MAC belt and disc sander, also listed for certain Scheppach and Woodster sanding machines.
Before ordering a replacement motor, always check the exact machine reference, the technical specifications and the electrical connections of the original component.
Electrical repairs must only be carried out with the machine disconnected from the power supply and by a suitably qualified person.
The electrical components of a belt and disc sander may also require replacement following a malfunction, wear or accidental damage.
The on/off switch controls the operation of the machine. If it becomes damaged, the sander may be difficult to start or may operate irregularly.
However, starting problems are not necessarily caused by a faulty switch. They may also result from the motor, power cable, electrical connections or another component within the electrical circuit.
It is therefore important to identify the cause of the malfunction before replacing any part.
Replacement electrical components must be selected according to their technical specifications and compatibility with the machine.
For safety reasons, a sander showing signs of an electrical fault must not be operated until it has been properly inspected and repaired.
Sanding belts and sanding discs are essential consumables for the proper operation of a combined woodworking sander. They must be replaced regularly to maintain sanding quality and prevent unnecessary strain on the machine.
The Mac Allister MBDP250 uses a 25.4 x 762 mm sanding belt and a 125 mm diameter sanding disc.
It is essential to select abrasives with the correct dimensions and an appropriate grit size for the intended application.
Coarse-grit abrasives are suitable for removing material quickly, shaping wooden components and correcting surface irregularities.
Medium-grit abrasives are generally used for everyday sanding operations, while finer grits are recommended for finishing work and preparing wooden surfaces before applying protective coatings.
A worn, torn or incorrectly aligned sanding belt may cause uneven sanding and potentially damage the machine's guiding components.
Similarly, a damaged sanding disc should be replaced before continuing work.
Regular replacement of abrasive consumables helps maintain efficient sanding performance and reduces unnecessary mechanical stress on the motor.
The correct operation of the Mac Allister MBDP250MAC belt and disc sander also depends on several mechanical components responsible for supporting, guiding and driving the abrasive systems.
The belt rollers and guiding mechanisms help keep the sanding belt running along its intended path.
Incorrect adjustment, mechanical wear or damaged components may cause the sanding belt to move sideways during operation.
Work tables, supports and adjustment mechanisms also play an important role in the accuracy and safety of sanding operations.
Depending on availability, certain mechanical components and accessories may be replaced individually to keep the machine in good working condition.
Before ordering, compare the required replacement part with the original component and carefully check the compatibility information provided on each product page.
To order the correct Mac Allister sander replacement part, it is essential to identify the exact model of your machine.
The reference MBDP250MAC should be checked on the machine's identification plate. Depending on the technical documentation, this sander may also be identified by the shorter reference MBDP250.
Before purchasing a replacement component, we recommend checking the following information:
Some woodworking machines may have undergone technical modifications during their production period.
For this reason, visual similarity alone is not sufficient to confirm that two components are interchangeable.
If you are unsure which part to order, a photograph of the original component together with the machine reference can help identify a suitable replacement.
Some components used on the Mac Allister MBDP250MAC belt and disc sander may also be compatible with sanding machines sold under other brand names.
For example, a replacement motor is available for the Scheppach BTS700, Scheppach BD7500 and Woodster BD75 sanders, as well as the Mac Allister MBDP250MAC.
This compatibility between different models can make it easier to find replacement parts, particularly when the original machine is no longer manufactured or widely available.
However, compatibility of a particular motor does not mean that all components from these different sanding machines are interchangeable.
Each replacement part must be checked individually according to its reference number, dimensions and technical specifications.
Regular maintenance of your Mac Allister belt and disc sander helps preserve its performance and reduce the risk of mechanical or electrical problems.
After each use, remove accumulated wood dust from the sanding areas, work tables and dust extraction openings.
It is also important to inspect the condition of the sanding belt and disc and regularly check the belt tracking adjustment.
A sanding belt that moves sideways during operation may wear prematurely or come into contact with protective components.
Recommended maintenance operations include:
Before carrying out maintenance, adjustment or replacement work, always switch off the machine and disconnect it from the electrical supply.
Using a suitable dust extraction system is also recommended to reduce the accumulation of wood dust during sanding operations.
Replacing a Mac Allister MBDP250MAC spare part can be a cost-effective solution when the rest of the machine remains in good working condition.
A localised mechanical or electrical fault does not always require the purchase of an entirely new sander.
Depending on the component involved and the cost of the repair, replacing only the defective part may be a practical alternative.
This approach helps extend the service life of workshop equipment, allows users to continue working with a familiar machine and reduces unnecessary equipment replacement.
However, it is important to ensure that the repair is technically appropriate and that all safety devices remain fully operational.
At Probois Machinoutils, we offer a selection of spare parts for Mac Allister sanders, along with compatible replacement components for various Scheppach, Woodster and other woodworking machines.
Our aim is to help customers maintain and repair their workshop equipment by providing clearly identified spare parts with useful compatibility information.
Browse the products available in this category to find replacement components suitable for your Mac Allister MBDP250MAC belt and disc sander.
If you cannot find the required part, please contact our customer service team with the exact machine model and, whenever possible, the original part number or a photograph of the component.
Explore our wider selection of Mac Allister machine spare parts to maintain and repair your other woodworking and DIY equipment.