Holzmann HBS470PROFI Band Saw Magnifier
Upper blade guide for Holzmann HBS470PROFI band saw
Light plate round shape for different band saws : Kity, Scheppach, Holzmann, Leman and Jean l'ébéniste
Complete angle guide groove 19 mm for band saw
Bearing 6201 for band saw and radial miter saw
Lower blade guide for Holzmann HBS470PROFI band saw
Start capacitor 50μF 450V reference CONDO50
230V switch for Holzmann HBS470PROFI and Leman SRU470 band saw
Blade guide wheel for Holzmann HBS470PROFI band saw
Contactor QKS8 for different Scheppach and Kity band saws
Rubber bandage for flywheel bandsaw Leman SRU470 and Holzmann HBS470PROFI
Are you looking for spare parts for your Holzmann HBS470PROFI bandsaw? At Probois Machinoutils, discover our selection of replacement parts designed for the maintenance, troubleshooting and repair of this woodworking bandsaw.
The Holzmann HBS470PROFI is a stationary bandsaw designed for various woodworking operations, including ripping, resawing thick timber, curved cutting and preparing wooden workpieces for joinery and cabinetmaking.
Like any woodworking machine, it contains mechanical and electrical components that may wear out or become damaged over time.
A worn drive belt can cause transmission problems. A damaged rubber wheel tyre can interfere with blade movement on the wheels. Incorrectly adjusted or deteriorated blade guides can affect cutting accuracy, while an electrical fault may prevent the machine from starting.
To help you repair your equipment without replacing the entire bandsaw, we offer a range of replacement parts for the Holzmann HBS470PROFI, including upper and lower wheels, rubber wheel tyres, a V-belt, blade guides, electrical components and guiding accessories.
Our catalogue is regularly updated to meet the maintenance and repair needs of bandsaw users.
Our selection includes various mechanical and electrical replacement parts, as well as accessories for your bandsaw:
Upper wheel for Holzmann HBS470PROFI bandsaw.
Lower wheel for Holzmann HBS470PROFI bandsaw.
Black rubber wheel tyre for 470 mm wheels, also compatible with the Leman SRU470.
V-belt for Holzmann HBS470PROFI.
Upper blade guide for Holzmann HBS470PROFI.
Lower blade guide for Holzmann HBS470PROFI.
Blade guide adjustment handwheel for Holzmann HBS470PROFI.
Complete mitre gauge for a 19 mm table slot.
Round table insert for various compatible bandsaws.
6201 bearing with a 32 mm outside diameter.
50 µF, 450 V permanent capacitor with wires, featuring an M8 screw mounting.
230 V KJD12 switch, also offered for the Leman SRU470.
14 A, 250 V QKS8 contactor for various woodworking machines.
Magnifying lens for Holzmann HBS470PROFI bandsaw.
These components allow you to work on the machine's main assemblies, including blade drive, blade guidance, adjustment mechanisms, electrical controls and cutting accessories.
Before ordering, it is essential to identify the exact part required and check its compatibility with your machine.
The wheels are essential components of a bandsaw. They allow the blade to move continuously and help keep it on its intended path.
The lower wheel is connected to the machine's drive system, while the upper wheel contributes to blade guidance and tension adjustment.
Our category includes two separate replacement parts:
The upper wheel for Holzmann HBS470PROFI.
The lower wheel for Holzmann HBS470PROFI.
These two components are not interchangeable.
A wheel may need replacing following a significant impact, deformation or mechanical damage.
Certain symptoms may justify a thorough inspection, including abnormal vibrations, irregular blade movement, unusual noise or difficulty maintaining stable blade tracking.
However, these symptoms do not necessarily mean that the wheel itself is defective.
A worn bearing, deteriorated rubber tyre, incorrect blade tension or improper adjustment can cause similar problems.
Before replacing an entire wheel, we therefore recommend inspecting all associated components.
The rubber wheel tyre for Holzmann HBS470PROFI is designed for 470 mm wheels.
It is also offered for the Leman SRU470 bandsaw.
Installed around the circumference of the wheel, this rubber tyre forms the contact surface between the wheel and the blade.
It contributes to smooth blade movement while preventing direct contact between the blade and the metal surface of the wheel.
Over time, the rubber may harden, crack, become deformed or begin to detach.
Several signs may indicate that replacement is necessary:
Cracks in the rubber.
A tyre beginning to detach from the wheel.
Visible deformation of its surface.
Significant or uneven wear.
Damage preventing the blade from tracking correctly.
A severely damaged tyre can interfere with the bandsaw's operation and contribute to vibrations.
However, before ordering, check that the problem is not caused by a damaged blade, incorrect tension or improper wheel adjustment.
After replacing the rubber tyre, it is essential to check blade positioning and tension before returning the machine to service.
The V-belt for Holzmann HBS470PROFI transmits movement from the motor to the bandsaw's drive system.
It therefore plays an essential role in the machine's operation.
A belt in good condition should provide smooth power transmission without excessive slipping or abnormal vibrations.
Over time, it may wear out, harden, crack or suffer accidental damage.
Several symptoms may justify inspecting the belt:
Visible cracks.
Significant wear on the belt's sides.
Slipping during operation.
Unusual noises coming from the transmission.
A broken or severely damaged belt.
A worn belt can reduce transmission efficiency and cause problems during cutting.
However, a machine that appears to lack power does not necessarily have a defective belt.
A blunt blade, unsuitable blade tension, excessive feed pressure or a motor problem can also explain reduced cutting performance.
Before ordering, check the belt reference and make sure that the pulleys and tensioning system are in good condition.
The upper blade guide for Holzmann HBS470PROFI bandsaw helps keep the blade in the correct position during cutting operations.
It limits sideways and backward blade movement when the blade is subjected to cutting forces.
Correctly adjusted blade guidance improves blade stability and contributes to consistent cutting results.
The upper guide must be positioned according to the manufacturer's instructions, particularly in relation to the height of the wooden workpiece.
Replacement may be necessary when the guide has mechanical damage that prevents it from functioning correctly.
This may include a broken support, a deformed component or a damaged adjustment mechanism.
Before replacing the complete guide, however, check that the problem is not simply caused by incorrect adjustment.
A blade that drifts during cutting may also be blunt, insufficiently tensioned or have an uneven tooth set.
The lower blade guide for Holzmann HBS470PROFI complements the upper blade guide.
Located beneath the worktable, it helps maintain the blade's position in the lower section of the machine.
Both guides must work together to limit unwanted blade movement during cutting.
The lower guide may need replacing if it has a broken component, a deformed support, excessive mechanical play or a damaged adjustment mechanism.
After replacing the lower guide, all blade adjustments must be checked.
The upper guide, lower guide, blade tension and blade positioning on the wheels must all be inspected according to the manufacturer's instructions.
A new blade guide will not compensate for a damaged or poorly sharpened blade.
Our selection also includes the blade guide adjustment handwheel for Holzmann HBS470PROFI.
This component operates its associated adjustment mechanism.
Replacement may be necessary if it is broken, cracked or no longer allows the intended adjustment to be carried out correctly.
Before ordering, however, make sure that the problem actually comes from the handwheel.
A damaged threaded rod, a seized mechanism or another defective component can cause similar adjustment difficulties.
After replacement, check that the mechanism operates correctly and that the guide can be secured in the required position.
The 6201 bearing offered in this category has an outside diameter of 32 mm.
It is intended for various compatible machines, including bandsaws and certain sliding mitre saws.
A bearing allows a mechanical component to rotate while reducing friction.
Depending on its location, it may contribute to the operation of a wheel or a blade guidance mechanism.
Over time, bearings can develop internal wear, excessive play or rotation difficulties.
The most common symptoms include:
Unusual noise during rotation.
Abnormal mechanical play.
Irregular rotation.
Roughness or tight spots.
Vibrations originating from the affected component.
A worn bearing must be replaced with a model having the appropriate specifications.
However, the 6201 designation alone is not sufficient to guarantee compatibility with every installation.
It is important to check the complete dimensions, the type of sealing or shielding and the reference indicated on the product page.
Our category includes a 50 µF, 450 V permanent capacitor, equipped with connecting wires and an M8 screw mounting.
Its stated dimensions are 45 mm in diameter and 117 mm in length.
A capacitor is an electrical component used in certain single-phase motors.
Depending on the motor's design, it helps create the phase shift required for the motor to operate.
A defective capacitor can cause starting difficulties, reduced torque or abnormal motor operation.
However, these symptoms can also originate from other electrical or mechanical components.
Before ordering a replacement capacitor, it is essential to check:
Its capacitance in microfarads.
Its rated voltage.
Its function within the electrical circuit.
Its connection type.
Its dimensions and mounting system.
Its compatibility with your machine's motor.
Important: a 50 µF capacitor is not automatically suitable for every bandsaw motor.
Capacitance alone is not sufficient to determine compatibility.
Capacitors can retain an electrical charge even when the machine is disconnected from the mains. Inspection and replacement must be carried out by a competent person.
The 230 V KJD12 switch offered in this category is intended for the Holzmann HBS470PROFI bandsaw and the Leman SRU470.
It forms part of the machine's electrical control system.
A switch may need replacing when its mechanism is broken or an electrical fault has been confirmed.
However, a bandsaw that refuses to start does not necessarily have a defective switch.
The problem may also originate from the power supply, a safety device, the motor or another component.
Before ordering, check the original switch reference, your machine's electrical voltage and the connection specifications.
This switch is specified for a 230 V supply. It must not be installed in another electrical configuration without confirmation of compatibility.
Never modify the wiring or safety devices to accommodate an unsuitable switch.
We also offer a 14 A, 250 V QKS8 contactor intended for various compatible woodworking machines.
This component forms part of the machine's electrical control system, according to the arrangement specified by the manufacturer.
A defective contactor can cause starting difficulties or prevent certain machines from operating normally.
However, these symptoms do not automatically mean that the contactor is faulty.
Before ordering, carefully compare the QKS8 reference, electrical specifications and connections with those of the original component.
Also check that your machine appears in the list of compatible models.
Work on electrical circuits must be carried out by a competent person.
The complete mitre gauge for Holzmann HBS470PROFI is designed for a 19 mm table slot.
This accessory allows you to guide a wooden workpiece at a specified angle during cutting operations suited to the machine's capabilities.
It can be used for certain crosscutting and angled cutting operations.
A mitre gauge may need replacing if it is broken, deformed or its adjustment mechanism no longer operates correctly.
Before ordering, check the width of your table slot and the specifications of the original gauge.
After installation, check the angle adjustment and make sure that the accessory moves correctly without coming into contact with the blade.
The round table insert, also known as a throat plate, fits around the opening through which the blade passes.
It helps reduce the space around the blade and provides a suitable support surface for wooden workpieces.
Our catalogue includes a table insert intended for various compatible bandsaws, including certain Kity, Scheppach, Holzmann, Leman and Jean l'Ébéniste models.
A table insert may become damaged following accidental contact with the blade or an impact.
When it is broken, severely cut or no longer remains securely in place, replacement may become necessary.
Before ordering, always check its dimensions, shape and the list of compatible machines.
A table insert intended for another bandsaw must never be considered interchangeable based solely on its visual appearance.
The magnifying lens for Holzmann HBS470PROFI is also among the replacement parts offered in this category.
It is a replacement component specific to the machine.
If it is broken, missing or damaged, replacing it allows you to restore the equipment with which it is associated.
Before ordering, check its reference and make sure that it corresponds to the original component fitted to your bandsaw.
A bandsaw that produces abnormal vibrations or cuts off line does not necessarily require new blade guides or wheels.
Several components may be responsible for the problem.
In particular, check the condition of the blade, its tension, the consistency of the tooth set, its position on the wheels and the condition of the rubber wheel tyres.
A blunt blade or one with an uneven tooth set may cause the cut to drift sideways.
Incorrectly adjusted blade guides may also allow excessive blade movement.
If the machine vibrates, inspect the bearings, V-belt, wheels and various mechanical mountings.
A deteriorated belt or worn bearing may contribute to irregular operation.
It is important to distinguish an adjustment problem from genuine mechanical damage.
An accurate diagnosis helps avoid unnecessarily replacing components that are still in good condition.
Before ordering a replacement part, identify your machine precisely.
We recommend recording the following information:
Brand: Holzmann.
Exact model: HBS470PROFI.
Machine's electrical voltage.
Serial number.
Manufacturing month and year.
Original part reference, if known.
Position number on the exploded diagram, where available.
This information is particularly important for electrical components and parts that may have changed between manufacturing versions.
Do not confuse the Holzmann HBS470PROFI with the HBS400, HBS450 or other bandsaws of similar dimensions.
Some parts in our catalogue are also compatible with the Leman SRU470, but this compatibility must not be assumed for every component.
IMPORTANT: BEFORE PURCHASING, you must check that your machine appears in the LIST OF COMPATIBLE MACHINES provided on the spare part product page. Where necessary, also check your machine's manufacturing month, manufacturing year and serial number.
Visual resemblance alone never guarantees the compatibility of a replacement part.
Regular maintenance helps preserve your bandsaw's performance and detect early signs of wear.
Before carrying out any work, disconnect the machine from the mains and wait until the blade has stopped completely.
Periodically inspect the condition of the rubber wheel tyres and check that they do not show cracks, deformation or signs of separation.
Also examine the V-belt to identify any signs of wear.
Check the bearings and make sure they do not have excessive play or produce unusual noise.
Inspect the upper and lower blade guides and their adjustment mechanisms.
Make sure that the blade is correctly tensioned and positioned on the wheels.
Regularly clean accessible areas to remove accumulated sawdust without damaging mechanical or electrical components.
After any repair, check that all covers and safety devices have been correctly refitted.
Never operate the bandsaw with an open cover or a disabled safety device.
If you notice abnormal vibrations, unusual noise or incorrect blade movement, stop the machine immediately.
A localised fault does not necessarily require purchasing a new bandsaw.
When a wheel, rubber tyre, drive belt, blade guide, bearing or electrical component has been confirmed as defective, replacing it may restore normal operation.
This approach helps extend the service life of your equipment.
However, it remains essential to confirm the cause of the problem before ordering.
A blade that drifts does not necessarily require new guides.
A wheel that produces noise does not always need to be replaced completely: a bearing may be responsible.
A machine that no longer starts does not automatically have a defective switch or capacitor.
An effective repair therefore depends on an accurate diagnosis and the selection of a fully compatible replacement part.
At Probois Machinoutils, discover a selection of spare parts for the maintenance and repair of your Holzmann HBS470PROFI bandsaw.
Upper and lower wheels, rubber wheel tyres, V-belt, blade guides, bearings, capacitor, switch, contactor and guiding accessories: our catalogue allows you to repair different parts of your machine.
Looking for another spare part for your Holzmann HBS470PROFI?
Send us the exact model, electrical voltage, serial number, manufacturing date and, if possible, the position number of the required part on the exploded diagram to help us identify it.
Probois Machinoutils: your specialist in spare parts for Holzmann woodworking machines, helping you maintain, repair and extend the service life of your HBS470PROFI bandsaw.
